Furman F1500-UPS E handleiding

Niet gecategoriseerd

Furman

76 pagina's

PDF beschikbaar

Handleiding

F1500-UPS E Front Panel Installation

The F1500-UPS E is shipped with the front panel unattached to ensure that no damage is caused during shipping. The front panel must be installed before using.

To ensure maximum battery life, it is highly recommended that you al-

low the battery of your F1500-UPS E to charge for at least six to eight

hours prior to initial use. Loss of charge can occur during shipping and

storage and it is best to allow the batteries to fully recharge before

operating the UPS under battery power. To recharge the battery, simply

leave the unit plugged into an AC outlet. The UPS will charge in the ON

as well as the OFF state. If you wish to use the software, connect the

enclosed USB cable to the USB port on the F1500-UPS E and an open

USB port on the computer or server.

DO NOT plug a space heater, vacuum cleaner, paper shredder or other

large electrical device into the F1500-UPS E. The power demands of

these devices will overload and possibly damage the UPS.

Plug the F1500-UPS E into a Schuko grounded receptacle. Make

sure that the branch circuit is protected by a fuse or circuit breaker

and does not service equipment with large electrical demands (e. g.

refrigerator, copier, etc.). Avoid using extension cords. If an extension

cord is used, the cord must be HAR certiﬁed for the country in which

the unit is deployed, minimum 1mm

, 3-wire grounded, and rated for

10 Amps. Power cord retainer clips are provided to secure the IEC end

of the power cord to the rear of the F1500-UPS E. The clips should be

installed using only the 3mm by 6.6mm screws provided with the UPS.

The F1500-UPS E will automatically charge the battery whenever it is

plugged into an AC outlet. To maintain optimal battery charge, leave the

F1500-UPS E plugged into an AC outlet at all times.

Installation

NOTE: To store your F1500-UPS E for an extended period, cover and

store it with the battery fully charged. Plug the unit in and recharge the

battery every three months to ensure maximum battery life.

COMMUNICATION INTERFACE

BlueBOLT™ Compatible (with BlueBOLT-CV1 interface card, sold sepa-

rately): provides remote access to reboot components, power equipment

on or off, and monitor power quality from anywhere in the world. Contact

Furman for price and availability.

The RS-232 communication card provided with the F1500-UPS E al-

lows connection and communication between the F1500-UPS E and an

automation, media server, or computer system. This allows an installer

to program a number of variables including the Critical Load Battery

Thresholds. See the software documentation for more information.

EXTERNAL BATTERY CONNECTORS

Furman’s BAT1500-EXT external battery pack (sold separately) offers

extended battery runtime when used in conjunction with the Furman

F1500-UPS E. Contact Furman for price and availability.

BANKS

1 2 3 4

POWER MENU

WIRING

FAULT

BANKS

1 2 3 4

POWER MENU

PROTECTION

BANKS

1 2 3 4

POWER MENU

PROTECTION

F1500-UPS E FRONT PANEL INSTALLATION

1. Remove front panel from shipping

inserts.

2. Verify that the battery connectors are

connected, red-to-red, black-to-black (pic).

If not connected, perform steps 2 and 6 in the

BATTERY REPLACEMENT section

3. (Optional) Install the supplied rubber

end-caps to the sides of the front panel.

Push the curved edge of the end-cap into

the mating slots of the front panel.

4. Carefully align the front

panel connector latches with the

slots in the F1500-UPS E.

5. Gradually apply pressure to the

left and right ends of the front panel

until you hear the latches ‘click’

1. Power off and unplug the UPS. Remove the front panel. Remove the rubber end caps and pull up on the latch mechanism.

Once the latch mechanism stops, gradually pull the front panel off of the F1500-UPS E.

2. Remove the screw from the battery connector security plate to release

the battery connector.

3. Disconnect both the red and black connectors.

4. Remove the screws from the battery pack (part number BC-1500) and pull the battery pack out of the unit using the integrated handle.

5. Install the new battery pack into the unit. DO NOT ATTEMPT TO REPLACE THE BATTERIES

IN THE ORIGINAL BATTERY PACK. IMPROPER INSTALLATION CAN RESULT IN FIRE OR

BATTERY LEAKAGE.

6. Reconnect the red and black connectors.

WARNING! ALWAYS CONNECT RED to RED and BLACK to BLACK.

If the cable connectors do not snap together easily as RED to RED

and BLACK to BLACK, NEVER attempt to force them together or connect

RED to BLACK which will cause electrical sparking, shock, fire or

explosion! Call Customer Service for help.

8. Reinstall the front panel per the Front Panel Installation instructions.

MB1500/F1500-UPS BATTERY REPLACEMENT

The F1500-UPS E is shipped with the front panel unattached to ensure that no damage is caused during shipping. Before the F1500-UPS E can be used, the front panel must be installed.

7. Reinstall the battery connector

security plate.

Bekijk gratis de handleiding van Furman F1500-UPS E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.