Furman ASD-120 2.0 handleiding

Niet gecategoriseerd

Furman

24 pagina's

PDF beschikbaar

Handleiding

CN-2400S Controls two ASD-120 2.0 Sequencers with an optional Fire Alarm Force OFF.

Diagram #5 illustrates a Furman CN-2400S Contractor Series controlling two

ASD-120 2.0 sequencers with a ﬁre alarm providing an emergency FORCE OFF:

1. CN-2400 S DELAY 3 RELAY OUTPUT (NC) and (C) terminals connect appropriately to

both ASD-120 2.0 units per the 12V and REM terminals with a parallel connection.

• (NC) to both 12V and (C) to both REM.

2. Conﬁgure Multi-Function DIP on the CN-2400S, factory default with DIP 4 UP.

• DIP 4 UP – (NO), verify factory default.

◦ • CN-2400S DIP 2 is also set UP for a longer delay time.

3. Fire alarm contacts connected to FORCE OFF terminals on both ASD-120s

(parallel connection).

• Conﬁgure DIP 4 switch on ASD-120 2.0 to NO or NC depending on the contact type.

used at the ﬁre alarm. Typically NC is the best terminal option for Event Production.

• Conﬁgure Multi-Function DIP on each ASD-120 2.0, factory default with DIP 4 UP.

• All Delay Bank LED indicators will ﬂash when FORCE OFF is activated.

• Optionally, the ﬁre alarm contacts can also be connected to the FORCE OFF terminals of the

CN-2400 S if desired.

4. Conﬁgure ASD-120 2.0 Multi-Function DIP for Normally Closed & Maintained Mode ON.

• DIP 4 UP – (NO), verify factory default.

• DIP 7 DOWN – MNT, verify factory default.

• ASD-120 2.0 DIP 1 is also set UP for a shorter delay time.

TWO ASD-120 2.0 UNITS CONTROLLED BY A CN-2400S AND BY FIRE ALARM

1 2 3 4 5 6 7

1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7

FORCE OFF

DELAY 3

CN-2400S DIP SETTINGS

ASD-120 2.0 DIP SETTINGS

FIRE ALARM

SYSTEM TRIGGER

+12V

STAT

REM

GND

REMOTE PORT

OPTIONAL

REMOTE

SWITCH

REMOTE

12V STAT REM GND

FORCE OFF

REMOTE

12V STAT REM GND

When the CN-2400S is sequenced ON, the CN-2400S unit’s DELAY 3 Contact Relay will trigger both

ASD-120 2.0 units to begin their respective programmed sequence.

Caution: The OFF sequence for the CN2400S and ASD-120 2.0 units will start at the same time.

In order to avoid timing conﬂicts while ramping down, the CN-2400S should be set to a longer delay time interval than all the time intervals on each ASD-120 2.0 sequencer.

ASD-120 2.0 ADVANCED INSTALLATION WITH FURMAN CN SERIES AND REMOTE RS-1 SWITCH

CN-2400S

DIP SETTINGS

ASD-120 2.0 DIP SETTINGS

FIRE ALARM

NO C NC

FORCE

REMOTE

12V STAT REM GND

DLY

ADJ

1 2 3 4 5 6 7

ALWAYS ON

ALWAYS OFF

*SET TO MIDDLE POSITION

DELAY OUTPUTS

NC A B C D E F NO

12V

REM

1 2 3 4 5 6 7 8 9

CN-2400S

DIP SETTINGS

1 2 3 4 5 6 7 8 9

CN-20MP

DIP SETTINGS

1 2 3 4 5 6 7 8 9

CN-20MP

DIP SETTINGS

1 2 3 4 5 6 7 8 9

CN-20MP

DIP SETTINGS

1 2 3 4 5 6 7 8 9

CN-20MP

DIP SETTINGS

1 2 3 4 5 6 7 8 9

12V

REM

Diagram Example #6

An ASD-120 2.0 Sequencer is controlled by a single RS-1 Remote System Control Panel and the

ASD-120 2.0 remotely activates Furman Contractor Series Products with Bank DELAY OUTPUTS A through F.

Diagram #6 illustrates a Furman ASD-120 2.0 sequencer controlling six Furman Contractor Series

units and a ﬁre alarm provides an optional FORCE OFF:

1. Connect CN-2400S and CN-20MP REM terminal pins to ASD-120 2.0 DELAY OUTPUT (NC)..

2. Connect a 12V terminal pin from each CN-2400S and CN-20MP to an appropriate

A through F pin at the ASD-120 2.0 DELAY OUTPUT interface.

3. Conﬁguration Multi-Function DIP on the CN-2400S units are factory default with DIP 4 UP.

• Only DIP 1 is set DOWN for a shorter than ASD-120 2.0 delay time on each CN-2400S unit.

4. Conﬁguration Multi-Function DIP on the CN-20MP units are factory default with DIP 4 UP.

• Only DIP 1 is set DOWN for a shorter than ASD-120 2.0 delay time on each CN-20MP unit.

5. Optionally, a ﬁre alarm can be connected to FORCE OFF

at the ASD-120 2.0, if desired.

• Conﬁgure Multi-Function DIP on the ASD-120 2.0, factory

default with DIP 4 UP.

• All Delay Bank LED indicators will ﬂash when FORCE OFF

is activated.

6. RS-1 terminals are connected to the ASD-120 2.0

REMOTE terminals, pole to pole:

• 12V to 12V, REM to REM, STAT to STAT, and GND to GND.

7. Conﬁgure ASD-120 2.0 Multi-Function DIP for

Normally Closed and Maintained Mode ON.

• ASD-120 2.0 DIP 2 is set UP for a longer delay time than

Contractor Series units.

• DIP 4 UP – (NO), verify factory default.

• DIP 7 DOWN – MNT, verify factory default.

• Ensure all Bypass Set DIP switches are SEQ.

• Set ASD-120 2.0 Key Switch to Remote.

ON/OFF Sequences are triggered by the RS-1 Key Switch or by the rotating the Key Switch to ON at the ASD-120 2.0 as an RS-1 override.

DIAGRAM EXAMPLE 5

DIAGRAM EXAMPLE 6

Bekijk gratis de handleiding van Furman ASD-120 2.0, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.