Frigidaire GMOS1968SS handleiding
Handleiding
Je bekijkt pagina 11 van 52
INSTALLATION OVERVIEW
IMPORTANT
NOTES:
• Make sure the screws for the blower motor and
blower plate are securely tightened when they
are reinstalled. Th
is will help to prevent
excessive vibration.
• Make sure the motor wiring has been properly
routed and secured, and that the wires are not
pinched.
Installation Instructions
Place the mounting plate against the wall and
in
sert the toggle wings into the holes in the
wall to mount the plate.
Tighten all bolts. Pull the plate away from the
wall to
help tighten the bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle
bol
ts. At least one wood screw must be used
to attach the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert
the bolts into the mounting plate
through the holes designated to go into
drywall and reattach the toggle wings to
3
⁄4″ (19 mm) onto each bolt.
1
Wall
M
o
un
ting
Pl
a
te
Spacing for
Toggles M
o
r
e
Than Wall
Thickness
Bolt End
T
o
g
gle
Bolt
Tog
g
le
Wings
To use toggle bolts:
2
RECIRCULATING (Non-Vented Ductless)
NOTE:
If the cabinet depth including the cabinet doors
NOTE: Before tightening toggle bolts and wood
s
crew, make sure the bottom of the mounting
plate touch the bottom of the cabinet when
pushed flush against the wall and that the plate is
properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the
wall.
A
A
1
. A
tta
ch Mounting Plate to Wall
Prepare T
op
Cab
inet
Check Blower Plate
Mount the Microwave Oven
Install or change Charcoal
Filter
A
2
.
A3.
A4.
A5.
A1.
Cabinet
Cabinet
(33 cm)
13" MAX.
is more than 13""'' then the unit must be
spaced out from wall using adequate materials
supporting
150 Ibs to allow proper top vent air exhaust/
intake.
3/8"TO
EDG
E
NO
TE
: IT IS VERY IM
POR
TANT TO
READ AND FOLLO
W
THEDIRECTIONS
IN THE INSTALLAT
ION INSTRUCTIONS
BE
F
O
RE PR
O
CEEDINGWITH TH
IS
REAR W
ALL TEMPLAT
E.
T
hi
s Rear
Wall Template serves to position
the bottom
mounting plateand to l
o
cate th
e h
or
i
zontal ex
hau
st
out
le
t.
1
. Us
e a le
velto check that the t
emplate
is p
os
ition
ed
accuratel
y
.
2. L
oca
te a
ndm
ark at le
a
s
t onestu
d
on theleft or
right
side of the c
e
nterli
ne
.
Itis import
an
t to use at le
as
t
one
wood
scre
w
mou
nte
d
fi
rmly in a
s
tud to suppor
t th
e weight
ofth
e micr
ow
ave
.
Mark two addi
tional, evenlyspa
c
ed
locatio
n
s for the
supplied toggle
bo
lts.
3. Drill hole
s in the
marked locations.Whe
r
e t
he
re is
a
stu
d
, d
r
ill a 3/16" hole
for woo
d screws. For holes
thatdo not line up with a s
tu
d, drill 5/8" h
oles fo
r
toggle bolts.
DO NOT INSTALL T
HE
MOU
NT
I
NG
PLA
T
E
A
T
THIS
T
IME.
4. Re
move the template fromthe r
ear
wal
l.
5.Revie
ht
w e In
sta
llationInstr
uc
tion book for
y
our
in
stallation
s
i
tuation.
Locate and mark holes to align with holes in the
mounting
p
late.
IMPO
RTANT
:
LO
C
AT
E AT LEAST
O
N
E STUD
ON EIT
HER
SID
E OF
TH
E CENTERLIN
E
.
MARKT
HE LO
CATION
FO
R 2 ADDITIONAL, EVENLY
SPACE
D TOGGLE BOLTS
IN
THE MOUNTING
PLATE
AREA
.
Locate and mark
holes to ali
gn with holes
in the
.
e
ta
lp
gn
itn
u
o
m
IMPO
RTANT
:
LOCAT
E AT LEAST ON
ESTUD ON EITHER SI
DE OF
THE
CENTER
LIN
E.
MARKT
HE LOCATIONFO
R 2 ADDITION
AL, EV
ENLY
SPACED
TO
G
GLE BO
LTS IN
THE MO
UN
TING PLATE
AREA
.
Trim t
he rear wall templat
e along
t
he do
tted line.
Trim the rear
wal
l t
emplat
e along
the dotted lin
e.
12"
4"
Darlevu
eltaa la ho
j
apara
c
o
nsul
t
a
r
la
v
e
r
s
i
ó
ne
nEs
paño
l.
EN-10
Bekijk gratis de handleiding van Frigidaire GMOS1968SS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Frigidaire |
| Model | GMOS1968SS |
| Categorie | Magnetron |
| Taal | Nederlands |
| Grootte | 10247 MB |
