Friedrich ZoneAire Select PZH07K3SB handleiding

Airco

Friedrich

37 pagina's

PDF beschikbaar

Handleiding

C. INSTALLATION OF THE UNIT

C.1 Pre-Installation Checkpoints

C.1.1 Before attempting any installation, carefully consider the following points:

Before attempting any installation, carefully consider the following points:

• Inspect all components and accessories for damage before and after installation.

• Remove the cardboard wall sleeve support and grill weatherboard.

• Check for proper wall sleeve installation in accordance with the wall sleeve installation instructions.

• Check for a subbase kit or other means of structural support which is required for ALL installations projecting more than 8” into room.

• Install the recommended Condensate Drain Kits for complete condensate removal.

• Ensure that the chassis is installed in a 16” high x 42” wide wall sleeve that is no deeper than 13 ¾”. A bafﬂe kit is required if the sleeve

exceeds that depth.

• Ensure that chassis and chassis front cover are installed and secured properly.

• Ensure that drapes, bed, bedspread, furniture, etc. DO NOT block either return or discharge air grilles.

• Inspect the condenser air inlet and outlet for any obstructions (shrubbery, etc.)

• Ensure that ‘reset’ button is pressed on LCD device (only on 230V models)

•

C.1.2 Important Considerations

C.1.3 Introduction to R32 Refrigerants

C.1.4 Additional Notes:

• The installation site should be in a well-ventilated condition.

• The sites for installing and maintaining an air conditioner using Refrigerant R32 should be free from open ﬁre or welding, smoking, drying

oven or any other heat source higher than 1000˚F which easily produces open ﬁre.

• When installing an air conditioner, it is necessary to take appropriate anti-static measures such as wear anti-static clothing and/or gloves.

• It is necessary to choose the site convenient for installation or maintenance wherein the air inlets and outlets of the indoor and outdoor

units should be not surrounded by obstacles or close to any heat source or combustible and/or explosive environment.

• If the indoor unit suffers refrigerant leak during the installation, all the personnel should go out till the refrigerant leaks completely for 15

minutes. If the product is damaged, it is a must to carry such damaged product back to the maintenance station and it is prohibited to weld

the refrigerant pipe or conduct other operations on the user’s site.

• It is necessary to choose the place where the inlet and outlet air of the indoor unit is even.

ASSEMBLING YOUR AIR CONDITIONER

Installation & Assembly Instructions

Important Considerations

1. Before installing the appliance, you must read the manual carefully to

get the safety informa and notes.

2. Unit refrigerant charge amount: refer to unit name plate marking.

3. A leak test must be done r the n is completed.

4. It is a must to do the safety  before maintaining or repairing

an air r using e refrigerant in order to ensure

that the e risk is reduced to minimum.

5. It is necessary to operate the machine under a controlled procedure

in order to ensure that any risk arising from the e gas or

vapor during the  is reduced to minimum.

Introduction to Refrigerants R32

1.Site Safety 2.Operation Safety

3.Installation Safety

- Refrigerant Leak Detector

- Appropriate  n

- The le picture is the  diagram of a refrigerant leak detector.

Please note that:

1. The inst site should be in a d .

2. The sites for installing and maintaining an air r using Refrigerant R32 should be

free from open  or welding, smoking, drying oven or any other heat source higher than

548 which easily produces open .

3. When installing an air , it is necessary to take appropriate t measures

such as wear  clothing and/or gloves.

4. It is necessary to choose the site convenient for  or maintenance wherein the air

inlets and outlets of the indoor and outdoor units should be not surrounded by obstacles

or close to any heat source or c and/or explosive environment.

5. If the indoor unit suers refrigerant leak during the , all the personnel should go

out  the refrigerant leaks completely for 15 minutes. If the product is damaged, it is a

must to carry such damaged product back to the maintenance s and it is

prohibited to

weld the refrigerant pipe or conduct other  on the user's site.

6. It is necessary to choose the place where the inlet and outlet air of the indoor unit is even.

7. It is necessary to avoid the places where there are other electrical products, power switch

plugs and sockets, kitchen cabinet, bed, sofa and other valuables right under the lines on

two sides of the indoor unit, and also prevent mechanical damage from occurring.

Open Flames

Prohibited



Necessary

Mind 

Electricity

Must Wear

 Clothing

and c

Gloves

Don't Use

Mobile Phone