Extron NBP 108 D handleiding
Handleiding
Je bekijkt pagina 49 van 73
Network Button Panels • Hardware Features and Installation — NBP 1200C 39
Step 9: Cable the NBP 1200C and Other Devices in the System
Bottom Panel Features (NBP 1200C)
NBP 1200C
LAN/PoE
RESET
LAN/PoE (Ethernet)
Connector and LEDs
Reset
LED and Button
MAC Address
Label
NBP 1200C Bottom Panel
MAC: 00-05-A6-XX-XX-XX
S/N:
XXXXXXX
E
XXXXXX
00-05-A6-XX-XX-XX
Figure 45. NBP 1200C Bottom Panel Features
Cabling
1. Run a network cable to the NBP 1200C.
2. Connect the NBP to the network via the LAN/PoE port on the bottom panel of the NBP 1200C (as shown in
gure 45). Details of LAN/PoE port connection, LED behavior, protocol, addresses, and credentials are shown
in figure 46.
LAN/PoE
RJ-45
Connector
NBP
Bottom Panel
LAN/PoE (Ethernet and
Power Over Ethernet)
Ethernet
NOTE:
MAC address information
(00-05-A6-XX-XX-XX) is located
on the bottom panel, next to the
LAN port.
PC
Link LED: Lights
green to indicate a
network connection.
Activity LED:
Blinks
amber to
indicate data
is being sent
or received.
TCP/IP
Network
Extron
Control
Processor
Connect to an Ethernet network.
This port must be congured.
Default protocol:
• NBP address: 192.168.254.253
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• Link speed and duplex level: autodetected
• Data rates: 10/100Base-T
Power over Ethernet (PoE):
The NBP receives power at this port.
Default login credentials:
• Username: admin or user
• Initial password: unit serial number
• Password after a “Full Factory Reset”:
extron
MAC: 00-05-A6-XX-XX-XX
S/N: XXXXXXX EXXXXXX
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: XXXXXXX EXXXXXX
MAC
Address
Figure 46. NBP 1200C LAN/PoE Port Details
IMPORTANT NOTES:
• The factory configured passwords for this device have been set to the device serial number.
Passwords are case sensitive. Performing a Full Factory Reset (see Resetting the Unit on
page 50) sets the passwords to
extron
.
• DHCP is off by default.
45
Cabling:
• For 10Base-T (10 Mbps)
networks, use a CAT 3 or better
cable.
• For 100Base-T (max. 155 Mbps)
networks, use a CAT 5 cable.
Activity LED (on connector) — This
yellow LED blinks to indicate network
activity.
Link LED (on connector) — This
green LED lights to indicate a good
network connection.
46
Rev. F: Changed
“admin” to “admin
or user” and updated
factory reset mode
name.
Rev. F: Changed
password text to plural.
Rev. C: Added notes about the
factory-set passwords being the
serial number and about DHCP
being off by default.
Bekijk gratis de handleiding van Extron NBP 108 D, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | NBP 108 D |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 12926 MB |
