Extron FOX3 SR 301 handleiding
Handleiding
Je bekijkt pagina 36 van 58
FOX3SR 301 and FOX3SR311 Scaling Receivers • SIS Configuration and Control 28
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Information requests (continued)
Information request
Verbose mode 2/3:
I SFPALnk
X2*
•
SFPBLnk
X2*
•
SigI
X$
•
HdcpI
X^
•
HdcpO
X&
•
AudI
X*
•
X(
•
X2(]
Inf00*SFPALnk
X2*
•
SFPBLnk
X2*
•
SigI
X$
•
HdcpI
X^
•
HdcpO
X&
•
AudI
X*
•
X(
•
X2(]
Response description:
Fiber link A•Fiber link B•Signal input•Input HDCP•Output HDCP•Input audio•Receiver•Fiber mode
]
Example:
I
SFPALnk1
•
SFPBLnk1
•
SigI1
•
HdcpI1
•
HdcpO1
•
AudI1
•
RX
•
SM
]
Signals are detected on the two fiber links, a signal is detected on the
input, the input and output are HDCP devices, the digital audio input is
selected, the device is a receiver, and the fiber mode is singlemode.
KEY:
X$
= Input video signal status 0 = Not detected 1 = Detected
X^
= Input HDCP status 0 = No source detected 1 = Source with HDCP detected (default)
2 = Source with no HDCP present
X&
= Output HDCP status 0 = No active sink detected 1 = Sink detected, output signal encrypted
2 = Sink detected, output signal not encrypted
X*
= Input audio selection 0 = Auto 1 = Digital 2 = Analog
X(
= Device type TX or RX
X2*
= Fiber link detection 0 = Not detected 1 = Detected
X2(
= Fiber optic mode SM or MM
DHCP client
Set DHCP on or off
E X1)
DH
}
Idh
X1)]
View DHCP status
E
DH
} X1)]
KEY:
X1)
= Set DHCP 0 = Off (default) 1 = On
Telnet port
Set Telnet port map
E
Z
X3%
PMAP
}
PmapZ
X3^]
Set Telnet port to
X3%.
View Telnet port map
E
ZPMAP
} X3^]
KEY:
X3%
= Enable Telnet port 23 0 = Off (default) 23 = Telnet port 23 enabled
X3^
= Port number Response is 5 digits with leading zeros, for example 00000 or 00023
Echo for SIS over SSH (port 22023)
Enable Echo
E
1ECHO
}
Echo1
]
Returns command entered with
response.
Disable Echo
E
0ECHO
}
Echo0
]
Returns response only.
View Echo status
E
ECHO
} X3)]
NOTE: The echo setting is for the current connection only, and remains until the connection is closed. Apply after connection is established.
KEY:
X3)
= Enable or disable 0 = Disable 1 = Enable (default)
Verbose mode
Set verbose mode
E X1&
CV
}
Vrb
X1&]
View verbose mode
E
CV
} X1&]
NOTE: Verbose mode will revert back to default in the event of a power cycle, disconnect from dataviewer, or disconnect from the Ethernet.
KEY:
X1&
= Verbose mode 0 = Clear/none (default for Ethernet) 1 = Verbose mode (default for RS-232)
2 = Tagged response for queries 3 = Verbose mode and tagged responses for queries
Timeout Ethernet data port
Set current port timeout
E
0*
X3!
TC
}
Pti0*
X3!]
View current port timeout
E
0TC
} X3!]
KEY:
X3!
= Timeout The number of seconds before timeout on IP connections (min=1, max=65000, with each number equivalent
to 10 seconds [default=30=300 seconds])
Bekijk gratis de handleiding van Extron FOX3 SR 301, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | FOX3 SR 301 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10927 MB |
