Extron Cable Cubby F55 handleiding
Handleiding
Je bekijkt pagina 3 van 12
3
Cut a Hole in the Table
Read the following information before making a cut in the table.
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the furniture.
ATTENTION : L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et
qualifiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
1. Choose one of the following methods for cutting the hole:
Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router
Cut-Out Template for t
he Extron
Cable Cubby F55
O
u
ter Ed
ge of Fron
t Bez
el
(D
o not cu
t th
i
s line.)
1.
Con
firm the prod
u
c
t to b
e in
s
ta
lled.
2
. Remove the s
u
rfa
c
e cut-out area
(gray) fr
om th
e template.
3.
Mea
s
ure th
e c
utout a
n
d
template.
4
. Mark
the position on th
e
furniture wher
e the Cable Cubby 1200
will be installed
.
5. Double check the dimen
sion
s
and p
os
ition,
then cut the opening.
Trim Ring
Lip
Cut-Ou
t Radius:
0.2
5" (
0
.6 cm)
User Access
P/
N
68-377
2
-
0
1 Rev.
A
Page
Size: 11" x 17
"
Print
Scale 1:1
Do not Shrink
If using a CNC wood router or other
precise machinery, use the exact
cut-out dimensions (see the table below).
Cut-out Dimensions
User Access
Width
Side
Dimension
Cable
Cubby
F55
10.50"
(267 mm)
6.00"
(152 mm)
Go to www.extron.com for routing
template part numbers and instructions.
Dimensions and cut-out templates are
available online at www.extron.com.
2. Measure and cut the hole in the surface where the enclosure will be installed.
Installing the Modules into the Cable Cubby F55 Enclosure
The Cable Cubby F55 enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations. These
modules can be installed either before or after the Cable Cubby F55 installation, in any slot of the enclosure. Determine where the
connectivity modules and power module will be installed in the enclosure.
NOTE: For a complete and up-to-date list of compatible modules, see the product page at www.extron.com.
Figure 3 shows the process for removing the supports in order to install a double-size module, such as the Flex55 AC+USB 130
US Power Module, into the Cable Cubby F55 enclosure. Half- and full-size modules can be snapped into the enclosure without
removing the supports (
1
).
1
Extron Cable Cubby F55
Enclosure
For a double-size module
installation, use pliers to
carefully twist the desired
support back and forth until
loose, and remove.
NOTE: Removal of a bridge support
is irreversible.
Figure 3. Removing a Support for a Double-sized Flex55 Module Installation
3
Bekijk gratis de handleiding van Extron Cable Cubby F55, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Extron |
| Model | Cable Cubby F55 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2893 MB |
