Ermenrich Ping SM60 handleiding
Handleiding
Je bekijkt pagina 6 van 30
6
EN
Ermenrich Ping SM60 Stud Detector
Please carefully read the safety instructions and the user manual before using this product. Keep away from children. Use
the device only as specified in the user manual.
Getting started
• Open the battery compartment cover (26) and insert 2 AAA batteries according to the correct polarity. Close the cover.
• Press the Power button (22) to turn the device on or off. The device enters the scanning on the ½" (13mm) depth mode by
default.
Calibration
Place the device flat against any surface that is free of studs, metal and AC cables. Turn the device on and select the desired
mode. Press and hold the Scan button (20) until the signal strength bars have decreased and the beeping sound is heard. This
indicates successful calibration. Do not move the device until the calibration is complete. Wait for 3 seconds after the calibration is
complete before using the device.
!
Calibration must be done each time a new mode is selected.
Usage
Stud detection mode
The device can scan the surface for wooden and/or metal studs on the depth of ½" (13mm), 1" (25mm) and 1½" (38m m). To
change between the modes, press the WOOD (Stud mode) button.
Choose the desired mode and complete the calibration. Place the device flat against the examined surface. Slowly move the
detector across the surface in the direction you want to scan. When the device detects the edge of a stud, the signal strength
bars (2) start increasing. Keep moving the device in the direction of the arrow indicator (8 or 14). When the device detects the
center of a stud, all of the signal strength bars are shown, the word "CENTER" appears at the top of the screen, and the bottom
of the screen displays signal strength in percent (100%). Keep moving the device in the same direction until the signal strength
bars decrease, and the other arrow appears on the screen. This point indicates the second edge of the stud.
!
If you are receiving erratic scanning results, it may be a result of humidity, moisture within the wall cavity or drywall, or
recently applied paint or wallpaper that isn’t fully dried.
!
This stud finder is not designed to scan materials such as: ceramic floor tile, carpeting and padding, plaster walls, foil
covered insulation board, glass, or any other dense material.
!
Remember that studs are typically placed 16" or 24" (41cm or 61cm) apart and are usually 1½" (38mm) wide. Anything
different might not be a stud.
Metal detection mode
The device can scan the surface for non-ferrous metals at a depth of 2½" (60mm) and for ferrous metals at a depth of 3" (80mm).
Press the METAL (Metal mode) button to select the metal detection mode. Complete the calibration and place the device flat
against the examined surface. Slowly move the detector across the surface in the direction you want to scan. Use the center
mark (1) to mark the point when there are most signal strength bars (2) on the screen (the device will also be steady beeping).
Keep moving the device in the same direction until the signal strength bars decrease. Start moving the device in the opposite
direction and mark the point where the signal strength bars are the fullest. The midpoint between the two marks is the center
of a metal object. If the device detects ferrous metal, the magnet icon (13) appears on the screen. If the device detects non-
ferrous metal, the icon changes to a strikethrough magnet (13).
To detect the location of the metal object more precisely, reduce the sensitivity of the device by calibrating it within the two
previously marked points. Calibrating on the surface with detected metal reduces the sensitivity and narrows the search area.
After the calibration is complete, repeat the above-mentioned steps within the two previously marked points. You can reduce
the sensitivity of the device multiple times to narrow the search area even more and locate the edges of a metal object with
greater accuracy.
Bekijk gratis de handleiding van Ermenrich Ping SM60, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ermenrich |
| Model | Ping SM60 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5032 MB |
