Electrolux EED-625 handleiding
Handleiding
Je bekijkt pagina 21 van 52
Installation manual
21
4.4 Mechanical installation
Foundation requirement
In this type of machine, the drum is attached directly to the frame. As a result the floor under the machine must be
stable enough to absorb the dynamic forces generated during spin cycles. For that reason, the mounting bolts must
be cast into the floor material itself.
When securing the machine to an existing concrete floor, it must be at least 200 mm / 7 7/8 inch thick, with a mini-
mum concrete strength of 20.7 MPa / 3000 psi. The floor must be free of seams and cracks.
If the floor is less than 200 mm / 7 7/8 inch, an alternative might be to cast a plinth. The floor must be able to with-
stand the loads indicated in the table in the Technical data section.
If an existing concrete floor (of 200 mm / 7 7/8 inch minimum thickness) is to serve as the foundation, but it is not pos-
sible to cast “J” bolts into the concrete, an alternative is to use so called chemical anchor bolts.
The machine must be securely fastened to a suitable foundation using 4–M16 (5/8 inch) threaded rod, heavy duty flat
washers and lock nuts or lock washers. Also two M10 (3/8 inch) expansion bolts (1) MUST be installed at the
front of the machine. If all six anchors are not properly installed, large vibrations in the machine’s cabinet
may occur.
Failure to properly secure the machine to its foundation, or securing the machine to an inadequate foundation, will re-
sult in severe vibration, damage to the machine, and will void the manufacturer’s warranty.
The following table shows the drilling points.
4-M16 (5/8")
2-M10 (3/8")
1
50 (1 15/16")
Ø 10 (3/8")
125 (5")
Ø 18 (11/16")
fig.5989E
mm
inch
A B C D E F G H I
EED-618 685
26 15/16
660
26
496
19 17/32
394
15 33/64
115
4 1/2
633.4
24 15/16
496
19 17/32
-
74.5
2 15/16
EED-620 725
28 9/16
660
26
496
19 17/32
443
17 7/16
115
4 1/2
665
26 3/16
496
19 17/32
-
74.5
2 15/16
EED-625 700
27 7/8
720
28 3/8
575
22 41/64
387
15 15/64
120
4 3/4
693.1
27 9/32
595
23 27/64
10
13/32
79
3 7/64
EED-630 785
30 7/8
720
28 3/8
575
22 41/64
495
19 31/64
120
4 3/4
758.7
29 7/8
595
23 27/64
10
13/32
79
3 7/64
EED-645 875
34 7/8
750
29 1/2
636.5
25 1/16
569.5
22 27/64
120
4 3/4
854.1
33 5/8
657.5
25 57/64
10.5
13/32
83.3
3 9/32
EED-665 950
37 3/8
830
32 11/16
716
28 3/16
633
24 59/64
125
4 15/16
955.7
37 5/8
738
29 1/16
11
7/16
86.3
3 25/64
EED-685 1035
40 3/4
910
35 13/16
789.5
31 5/64
696
27 13/32
135
5 5/16
1052.5
41 7/16
811.5
31 61/64
11
7/16
94.5
3 23/32
Mark and drill all holes for bolts in the positions shown.
Fix the thread rod M16 to the floor.
Bekijk gratis de handleiding van Electrolux EED-625, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Electrolux |
| Model | EED-625 |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 4390 MB |
