Elation Waterfall 250 handleiding

Verlichting

Elation

8 pagina's

PDF beschikbaar

Handleiding

Waterfall 250™ Operation

Stand Alone:

This function is used when using only one unit or running more

than one unit as individual fixtures. See page 10 for detailed info of

dipswitch traits.

A. Set dipswitch 10 to the “On” position.

B. Plug the unit in, the unit will react to sound via an internal

microphone.

C. Use the audio sensitivity knob on the rear of the unit to make the

unit more or less sensitive to sound. Turning the knob in a clock-

wise direction will make the unit more sensitive to sound.

Master / Slave Operation:

This function will allow you to link up to 4 units together. In this mode,

the units will react to sound via the master units’ internal microphone.

The units will run to the built in programs of the unit functioning as

the master.

A. Use XLR cables to daisy chain the fixtures together. Remembering

the female XLR is the output, and the male XLR is the input.

B. Be sure to follow the dipswitch chart on page 9.

C. For longer cable runs, we suggest a terminator at the last fixture in

the cable run (see terminator on page 7).

Universal DMX Control:

This function allows you to use a universal DMX controller such as

the LSC® Show Designer 2.™ The use of a DMX controller will allow

you to customize the operation of the fixture allowing you to have

independent control of the color wheel and the ability to black out the

lamp. This will allow you to create your own programs or use your fix-

tures as textured color changers.

A. The Waterfall 250™

is a three channel DMX fixture.

B. When using a DMX controller and setting up for DMX operation

follow the standard DMX Binary Code for a three (3) channel unit.

Channel 1 is color, channel 2 is glass wheel 1, and channel 3 is

glass wheel 2.

C. For help running in DMX mode consult the manual that came

with your DMX controller.

D. For longer cable runs we suggest a terminator at the last fixture

(see terminator on page 7).

©Elation Professional® - www.elationlighting.com - Waterfall 250™Instruction Manual Page 7 ©Elation Professional® - www.elationlighting.com - Waterfall 250™Instruction Manual Page 8

Waterfall 250™ Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problem

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer cable runs are used,

you should use a terminator pin on the last unit to avoid erratic behav-

ior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected

between pins 2 and 3 of a male XLR connector (DATA + and DATA -).

This pin is inserted in the female XLR connector of the last unit in your

daisy chain to terminate the line. Using a cable terminator (ADJ part

number Z-DMX/T) will decrease the possibilities of erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line, a cable adaptor must be used,

these adaptors are readily available at most professional sound and

lighting stores. The chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Figure 3

Bekijk gratis de handleiding van Elation Waterfall 250, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.