Elation ELED Fresnel 150 handleiding

Verlichting

Elation

6 pagina's

PDF beschikbaar

Handleiding

LED Display:

The LED display will shut off after 15 seconds of inactivity. To make the

display reappear press and hold any button for at least 6 seconds.

Operating Modes:

Master-Slave Operation:

This function will allows you to link units together to run in a Master-

Slave mode. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units built-in programs.

Any unit can act as a Master or as a Slave however, only one unit can be

programmed to act as the “Master.”

Master-Slave Connections and Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit.

Use standard XLR cables to link your units together. Remember that

the Male XLR connector is the input and the Female XLR connector

is the ouput. The first unit in the chain (master) will use the female

XLR connector only. The last unit in the chain will use the male XLR

connector only.

2. Set the “Master” unit to your desired mode of operation.

3. For the “Slave” unit(s), press the MODE button until “XXX3” is dis-

played.

4. Connect the “Slave” unit or units and they will automatically start to

follow the “Master.”

Manual Dimmer:

1. Plug the fixture in and press the MODE button until “XXX4” is dis-

played.

2. Use the UP and DOWN buttons to adjust the LED intensity.

This onboard control mode is regulated by the output setting.

Output Setting:

The Output Setting will set the output wattage level for manual control

and DMX dimming output.

1. Plug the fixture in and press the MODE button until “XXX5” is dis-

played. Either “1005” (100W) or “1505” (150W) will be displayed.

2. To change the setting press and hold the UP button for at least 6

seconds to change to 150W output, or press and hold the DOWN

button to change to 100W output.

ELED Fresnel 150 Operating Instructions

Elation Professional - www.elationlighting.com - ELED Fresnel 150 Instruction Manual Page 8Elation Professional - www.elationlighting.com - ELED Fresnel 150 Instruction Manual Page 7

DMX Mode:

Operating through a DMX controller gives the user the freedom to create

their own programs tailored to their own individual needs. This function

also allows you to use your fixtures as spot lights. The ELED Fresnel 150

has 3 DMX modes: 1 Channel mode, 2 Channel mode - mode 1, and 2

Channel mode - mode 2. See page 9 for each modes’ DMX traits.

1. This function will allow you to control each individual fixture’s traits

with a standard DMX 512 controller such as the Elation® Show

Designer™ or the Elation® DMX Operator™.

2. To run your fixture in DMX mode, plug in the fixture via the XLR con-

nections to any standard DMX controller. Select your desired DMX

mode, and then press the UP or DOWN buttons to adjust the DMX

address. XXX = DMX Address

3. To run the 1 Channel Mode, press the MODE button until “XXX1”

is displayed. This is the DMX addressing for the 1 Channel DMX

Mode.

4. To run the 2 Channel Mode - Mode 1, press the MODE button

until “XXX2” is displayed. This is the DMX addressing for the 2

Channel DMX Mode - Mode 1.

5. To run the 2 Channel Mode - Mode 2, press the MODE button

until “XXX3” is displayed. This is the DMX addressing for the 2

Channel DMX Mode - Mode 2.

6. Please see page 9 for DMX values and traits

ELED Fresnel 150 Operating Instructions

Bekijk gratis de handleiding van Elation ELED Fresnel 150, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.