Ecoteck Libera handleiding
Handleiding
Je bekijkt pagina 39 van 48
Use and maintenance manual, model “LIBERA 8 V/C - LIBERA 11 V/C”
ENGLISH
39
ALARM CODE REASON
15 - ASH
DRAWER OPEN
The ash drawer was forgotten open,
placed, or closed incorrectly while
cleaning the product.
SOLUTION
Check the correct closure and/or the
correct insertion of the ash drawer in its
housing.
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
18 - FLAME
PROBE
Simultaneous failure of the ame and
smoke temperature probes.
SOLUTION
Contact the Authorised Support Centre.
ALARM CODE REASON
22 - FLAME
TEMPERATURE
An obstruction in the brazier, or in the
internal passages of the appliance, is
hindering proper combustion. This can
be due to the use of fuel other than
recommended;
SOLUTION
Turn the product off and on again to
activate the cleaner; adjust combustion
with “P/A Ratio”.
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
23 - AUGER
TRIAC
Anomaly in a component inside the
electronic board that manages the
loading motor, or the automatic
mechanical cleaner.
The cause may be due to possible
voltage drops, incorrect input voltage
to the appliance, lack of earthing in the
home's electrical system, or in the socket
to which the appliance is connected.
SOLUTION
Have the power supply voltage checked
by a trusted electrician. Try to turn the
plug in the wall socket to reverse Phase
and Neutral - if this xes the problem, the
problems lies in the earthing.
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
Unscrew the protective cap and press the
button to reset the circuit breaker after
having lowered the temperatures.
MANUAL RESET
THERMAL
SWITCH
24 - AUGER
PHASE
Erratic voltage detected between the
electronic board and the loading/
cleaning gearmotors.
SOLUTION
Have the power supply voltage checked
by a trusted electrician. Try to turn the
plug in the wall socket to reverse Phase
and Neutral - if this xes the problem, the
problems lies in the earthing.
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
28 - FAULTY
SMOKE
ENCODER
The sensor that checks the correct
functioning of the smoke extractor has
failed, or the signal no longer reaches the
electronic board.
SOLUTION
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
29 - CLEANING
CYCLE LIMIT
The maximum number of automatic
brazier-cleaning cycles allowed over
a prolonged period of use has been
reached.
SOLUTION
Safely, vacuum the brazier and turn on
the product again.
At the end of the winter season, clean
the stove thoroughly, even if the “service
hours” does not show up.
If the problem persists, contact the
Authorized Assistance Service.
ALARM CODE REASON
33 - PELLET AIR
LEVER CLOSED
The combustion air adjustment lever for
WOOD operation is in a wrong position
and this prevents the product to start in
pellet mode.
SOLUTION
Lift the lever to start the product in pellet
mode.
If the problem persists, contact the
Authorized Assistance Service.
19 PRODUCT CLEANING
The installation must guarantee easy access to
all parts of the generator and to the combustion
smoke evacuation system, in case of extraordinary
maintenance and any repair work.
Please carefully follow the instructions provided in
this chapter to carry out correct routine cleaning
and keep the generator functioning and in good
condition.
Failure to carry out maintenance could cause
operating problems, even serious ones, not
covered by the warranty.
Bekijk gratis de handleiding van Ecoteck Libera, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ecoteck |
| Model | Libera |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9584 MB |
