Ecoteck Libera handleiding
Handleiding
Je bekijkt pagina 18 van 48
Use and maintenance manual, model “LIBERA 8 V/C - LIBERA 11 V/C”
ENGLISH
18
Follow the instructions displayed on the remote
control to pair it with the stove, as shown in the
following gure.
AUTO
To start the connection procedure, hold down
the pairing button on the electronic board (the
one in the centre of the three available) for a few
seconds, until the orange LED starts ashing, as
highlighted in the image following. The electronic
board is located on the right side of the product.
Press OK on the remote control (you may need
to press it twice), to automatically connect the
devices via the best frequency.
A check mark will appear on-screen, followed
by an acoustic signal, indicating that the remote
connection was successful.
When replacing the batteries, you will not need
to pair your remote control again. When asked
“FIRST INSTALLATION?”, select NO and press OK to
conrm.
In case interferences prevent the automatic
association, it is possible to force a xed channel
- CH1 or CH2 - with the arrow keys ↑ ↓, repeating
the connection procedure (i.e., inserting the
batteries, and then answering YES to “rst
installation?”) when the display shows the message
inviting you to press the button on the electronic
board, before pressing it, use the arrow keys on
the remote control to choose one of the two xed
channels instead of AUTO. If the interference is
still disturbing the connection, nd its source (the
device emitting it) and have it checked by its
manufacturer's technical assistance.
AUTO
CH 1
↓
↓
CH 2
6.2 THERMOSTAT (EXT.T) CONNECTION
If you want to manage the appliance from a
different room (from which the remote control
cannot work), it is possible to connect an external
thermostat to the product to modulate the
combustion or to control the appliance switch-on
and off (this can be done by activating a specic
function). As in the gure below, connect the
thermostat terminals to the terminal block on the
back of the product (near the emergency panel).
TERMINAL
EXTERNAL THERMOSTAT
The external thermostat MUST operate with a
"clean” or “dry”, generally in closed mode,
otherwise the electronic control unit will be
damaged. Once connected to the power
system, activate the recognition function from
the SETTINGS menu (see paragraph “ENABLE
EXTERNAL THERMOSTAT”) to allow the control
unit to recognize the presence of the external
thermostat.
By activating the function that allows to enable the
external thermostat, temperature management
and reading will be inhibited on the remote
control. If the room temperature has not yet been
reached, the display shows “TON”, otherwise it will
show “TOFF”.
6.3 FUEL LOADING
PELLETS
To fuel the stove, just lift the lid of the pellet tank
that you can nd on the top side of the product
and pour the pellets into it. Verify that the bag
of pellets does not fall around the edges of the
tank, paying particular attention to centring while
loading.
Also, pay attention to the following:
• do not let the package of the pellets come into
contact with hot surfaces during operation or
shortly after the product has been turned off;
• avoid dumping into the tank any residual sawdust
found at the bottom of the bag of pellets.
Load pellets only when the stove is off and cold.
Make sure to close the tank lid properly after
loading. FOR SAFETY REASONS, on certain models
the closure is controlled electronically. If the lid is
not closed correctly, an acoustic signal warns the
user to close it as soon as possible. In this case the
pellet loading is interrupted. Ignoring the alarm
will trigger an alarm.
Bekijk gratis de handleiding van Ecoteck Libera, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ecoteck |
| Model | Libera |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9584 MB |
