Handleiding
Je bekijkt pagina 12 van 16
8. Operation
8.1 Start Up/Shutdown
1. Plug in and the display screen with come on and the
SPEED indicator will ash.
2. To select an operating mode press the POWER
button (10) or use the remote control. Note: The unit
will default to FAN mode.
3. To stop the operation press the POWER button again.
4. Allow the unit to completely stop before unplugging.
8.2 Operation Modes (11)
• The unit has four operation modes: COOL,
DEHUMIDIFIER (DRY), FAN or SLEEP.
• To change from °C Centigrade to °F Fahrenheit either
hold the MODE button down for 2-3 seconds or press
the °C /°F button on the remote control to switch.
8.2.1 Cooling Mode (12a)
1. Press the MODE button until the COOL indicator
lights up.
2. Press the UP and DOWN buttons to adjust the
required temperature. The temperature can be set
between 16°C and 32°C.
3. Press the SPEED button until the desired fan speed
indicator lights up. To control the direction of the air
ow, press the SWING button (15).
Note: The air conditioner will stop if the room
temperature is lower than the selected temperature.
8.2.2 Dehumidier/Dry Mode (12b)
1. Press the MODE button on the control panel until the
dehumidier indicator lights up. Remove the drain
valve plug and connect the drainage hose (E ) to the
drain outlet (8) at the bottom of the unit.
Note: In this mode, the fan speed is on low and a
temperature cannot be selected.
2. Refer to section 9.1 Manual Drainage and 9.2
Continuous Drainage for more information on using
the drainage hose.
8.2.3 Ventilation/Fan Only Mode (12c)
1. Press the MODE button until the FAN indicator lights
up.
Note: In ventilation mode the room air is circulated,
but not cooled.
2. Press the SPEED button to select the desired fan
speed.
8.2.4 Sleep Mode (13)
1. The SLEEP mode can be activated when in COOL
mode by pressing the button on the control panel or
by selecting on the remote control.
2. In SLEEP mode: the display screen light will dim and
the fan will operate at low speed.
8.2.5 Timer Setting – 1hour – 24hours (18)
The timer operates in two ways:
a. To Turn O (when power on) – Press the TIMER
button to select the timer function. Then press the UP
and DOWN arrows until the delay o time required is
set.
b. To Turn ON (when power o) - Press the TIMER
button to select the timer function. Then press the UP
and DOWN arrows until the delay on time required is
set.
To cancel the timer – Press UP/DOWN until ‘00’ is
displayed or press the POWER button.
8.2.6 Automatic Defrost
At low room temperatures, frost may build up at the
evaporator during operation. If this occurs the unit will
start defrosting and the power light will blink.
The unit will automatically start defrosting and the
POWER light will blink.
The defrost operates as follows:
a. When the unit operates in the COOL or
DEHUMIDIFIER/DRY mode, the temperature sensor
will sense the evaporator coil temperature is below
-1°C. The compressor will then stop operating for 10
minutes or until the temperature reaches 7°C, the unit
will then restart in COOL mode.
b. When the unit operates in the dehumidifying mode,
once the coil temperature sensor senses the
temperature of the evaporator is below 40°C and the
dierence between the coil temperature and room
temperature is below 19°C, the compressor will
operate for 20minutes. The unit will then start
defrosting for 5 minutes and the POWER indicator
will blink.
8.2.7 Overload Protection
In the event of a power loss, to protect the compressor
there is a 3 minute delay until the compressor will restart.
– 12 –
Bekijk gratis de handleiding van Draper 23833, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Draper |
| Model | 23833 |
| Categorie | Airco |
| Taal | Nederlands |
| Grootte | 1983 MB |