Dotco 10L2565-01 handleiding

Handleiding

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768/ 68

Afdrukken

Je bekijkt pagina 2 van 68

Page 2

GS-2007

02-2014

PRODUCT DESCRIPTION:

Pneumaticgrindersareportablehandheldtoolspowered

by compressed air. The motor drives a rotating spindle

onwhichagrindingwheelorotherabrasivedeviceis

mounted.Whenapplicable,thegrinderisequippedwith

a guard.

Failure to observe all safety warnings could result in

equipment damage or personnel injury.

INTENDED USE:

A pneumatic grinder is to be used only for removing

materialbyutilizingappropriateabrasivewheels,rotary

les or other material removal cutting devices. The

grinder must not be modied in any manner unless

approvedinwritingbyApexToolGroup,LLCorApex

Tool Group GmbH & Co. OHG. All safety devices must

be properly installed and maintained in good working

order.

Any abuse or misuse of the cutting device can be

extremelydangerous.

GENERAL SAFETY INSTRUCTIONS:

These Safety Instructions must be accessible to the

operatoratalltimes.Theymustbeshownandmade

available to all personnel involved in the operation of this

equipment.

The operator must read and understand the

Safety Instructions contained in this document

before operating this equipment.

These Safety Instructions are not intended to be all

inclusive. The operator should also read and understand

the Product Manual for the specic tool. Study and

comply with all applicable Federal, State and Local

Regulations.

Do not remove any labels from this equipment. Replace

any label that has been damaged and can not be easily

read.

PRODUCT INSTALLATION:

Only qualied and trained personnel should install,

adjust or use this equipment.

WORK ENVIRONMENT:

Thework areamust beclean, uncluttered,thoroughly

ventilatedandwellilluminated.

Make sure the work environment is free of

anyammable orcombustibleelements that

sparks from the grinding process could ignite.

SPEED CHECK:

Checkthetoolspeedbeforemountingawheel,afterany

repairs,wheneverthetoolisissuedforuseorevery24

hours.TheRPMofthegrindermustbecheckedwitha

calibrated tachometer to make certain its actual speed

doesnotexceeditsratedspeed.

Carefullydetermineifthereisamaximumspeedmarked

on the cutting device. If so, this speed must be greater

thantheratedspeedofthetool.Failuretocomplywith

this instruction could result in serious injury or death.

GRINDING WHEEL INSPECTION:

Allgrindingwheelsshouldbecloselyinspectedbefore

installation and use. Consult the safety procedures of

thegrindingwheelmanufacturer.Includeblotterswhen

required.

PROPER ABRASIVE MOUNTING:

Therearemanytypesofcuttingwheelsincludingstraight,

cone, plug, cup, depressed center and mounted. Consult

and complywith theSafety Instructions ofthe cutting

wheel manufacturer. Insure the proper manufacturer

recommendedspindle,angesandguardsarepresent

on the tool.

Alwaysuseproperlymountedguards,asprescribedfor

the cutting device being used per ANSI/CAGI B186.1. If

the guard has been damaged, it must be discarded and

replaced.

Generally,rotarylesandsomeothercuttingdevicesdo

notrequirewheelguards.Conrmthiswiththecuttingtool

manufacturerandconformwiththeirrecommendations.

After mounting the cutting device and guard, the tool

should be started under a steel bench or similarly

protective area. Make sure safety glasses are worn.

Run at full speed for at least one minute to insure proper

operation.

GRINDING WITHOUT A GUARD:

Operators may use the grinder without a

guardonlyiftheyfollowtheserequirements.

Improper use of agrinder without a guard,

includingfailuretofollowtheserequirements,

could result in seriour injury or death.

Type 1 Wheel: Do not use a wheel larger than 2”

(50mm) in diameter or more than 1/2” (13mm) thick.

Neverexceedaperipheralspeedof1800surfacefeet

per minute (548.64m/min).

Type 1 Reinforced Wheel:Donotuseawheellarger

than3”(76mm)indiameterormorethan1/4”(6.4mm)

thick.Neverexceedaperipheralspeedof9500surface

feetperminute(2895.6m/min).

Grinding Wheels:Usedforinternalwork,whilewithin

theworkbeingground.

Mounted Wheels:Donotuseamountedwheelwitha

diametergreaterthan2”(50mm).

Other Cutting Devices: Do not use small cones, plugs,

threaded hole pot balls, or other similar devices that

exceed 3” (75mm) in diameter and 5” (125mm) long

withoutaguardunlesstheworkprovidesprotection.

CUT-OFF WHEELS (Type 1 and Type 27):

Securetheworkpiecetoprovideacleancutandreduce

the possibility of binding.

Ifthecut-offwheelbecomesjammed,turnthegrinder

offandfreethewheel.Makesurethewheelissecurely

attached and not damaged before continuing the

operation.

Never use a cut-off wheel to perform a side grinding

operation.

ENGeneral Safety

Pneumatic Grinders

WARNING

WARNING

WARNING

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768/ 68

Bekijk gratis de handleiding van Dotco 10L2565-01, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Gerelateerde producten van Dotco (Niet gecategoriseerd)

Handleiding bekijken

Dotco 10N2080-01

Niet gecategoriseerd - handleiding

Andere merken in Niet gecategoriseerd