Dirt Devil QuickFlip SD68000 handleiding
Handleiding
Je bekijkt pagina 4 van 18
BLOWING OPERATION
This Wet/Dry Vac has blowing capabilities. To use
the blower feature, follow the instructions listed.
WARNING: Always wear safety
goggles complying with ansi z87.1 (Or, in
canada, csaz94.3) Before using blower.
CAUTION: Keep bystanders clear from
blowing debris.
WARNING: Wear a dust mask if
blowing creates dust that might be inhaled.
1.
Verify that the power cord is disconnected from
the outlet.
2.
Make sure the collection tank is empty before
using as a blower.
3.
Remove hose from the vacuum port.
4.
Insert the locking end of the hose into the
blowing port on the back side of the power head
and lock into position.
5.
Fit the desired extension wand and or nozzle to
the vacuum hose.
6.
Ensure the power switch is turned o and plug in
the power supply.
7.
Before turning on the vac, firmly hold the loose
end of the hose. Turn the motor on by pressing
the switch to the ‘I’ ON position.
CARE AND MAINTENANCE
1.
Verify that the power cord is disconnected from
the outlet.
2.
Disconnect the hose from the vacuum.
3.
Undo the latches and remove the power head
from the collection tank.
4.
Clear all dirt or debris from the collection tank
and hose.
5.
Check the hose, attachments, and power cord to
verify that they have not been damaged.
IMPORTANT: Clean or change the cartridge
filter regularly for best performance.
ALWAYS USE DUST FILTER FOR DRY VACUUMING.
If the machine is used without the dust filter,
the motor will burn out and the warranty will be
voided. Always keep spare dust filters on hand.
NOTICE: The filters included are made of high
quality materials designed to stop small dust
particles. The dust filter should be used for dry
pick-up only. A dry dust filter is necessary to
pick up dust. If the dust filter is wet, it will clog
quickly and be dicult to clean. Handle the
filter carefully when removing it for cleaning or
replacing. Check the filters for tears or small
holes. A small hole can let dust pass through and
out of the cleaner. Do not use a filter with holes
or tears in it; replace it immediately.
WARNING: Always disconnect the
plug from the power outlet before removing the
power head from collection tank.
INSTALLING & CLEANING
CARTRIDGE FILTERS
INSTALLING CARTRIDGE FILTER
1.
Verify that the power cord is disconnected from
the outlet.
2.
Remove power head and place in upside down
position.
3
Install the cartridge filter over the filter cage
with the flat end of the filter towards the vacuum
power head. Carefully push the filter in until it
stops against the power head.
4.
Place filter retainer on top of cartridge filter
over the raised lip and tighten down by turning
retainer clockwise, taking care not to over-
tighten.
REMOVING AND CLEANING CARTRIDGE
FILTER
1.
Unlock and remove the filter retainer by tuning
retainer handle counterclockwise.
2.
Carefully hold and pull the cartridge filter upward
to remove.
3.
Clean the cartridge filter by gently tapping or
brushing dirt o. Cleaning should not be done
indoors in living areas. For optimal performance,
a new filter is recommended.
4.
Install cleaned or new filter into place as
instructed above in steps 2 and 3 of Installing
Cartridge Filter.
5.
Wet filters should be removed and allowed to air
dry for 24 hours before installing onto the filter
cage.
Bekijk gratis de handleiding van Dirt Devil QuickFlip SD68000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dirt Devil |
| Model | QuickFlip SD68000 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 7025 MB |
