Dirt Devil QuickFlip SD68000 handleiding
Handleiding
Je bekijkt pagina 3 van 18
10.
Choose the desired accessories and push onto
the vacuum hose.
POLARIZED PLUG
To reduce the risk of electrical shock, this
appliance has a polarized plug (with one blade
wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug
in any way. Double
insulation eliminates the
need for the three wire grounded power cord and
grounded power supply system.
DRY-VACUUM OPERATION
DRY VACUUMING
WARNING: Be sure to read,
understand, and apply information entitled
“SAFETY INFORMATION”. Do not vacuum
in areas with flammable gases, vapors, or
explosive dusts in the air. Flammable gases or
vapors include but are not limited to: lighter
fluid, solvent type cleaners, oil-based paints,
gasoline, alcohol, or aerosol sprays. Explosive
dusts include but are not limited to: coal,
magnesium, grain, or gun powder. To reduce the
risk of health hazards from vapors or dust, do
not vacuum toxic materials.
1.
Verify that the power cord is disconnected from
the outlet.
2.
In order to prepare your vacuum for dry
vacuuming, verify that the cartridge filter is
securely mounted. With power head removed and
in upside down position, make sure the filter is
pushed in until it stops against the power head
and the retainer is installed.
3.
Place the power head section back on the
collection tank and secure it in place using the
latches.
OPERATING INSTRUCTIONS: DRY
VACUUMING
4.
Insert the locking end of the hose into the
vacuum port on the power head and lock in place.
Push the required attachment onto the free end of
the hose or extension.
5.
Plug the power cord into the outlet.
6.
Turn the motor on by pressing the switch to the
‘I’ ON position.
7.
Once you have completed vacuuming, press the
switch to the ‘O’ OFF position and unplug the
power cord from the outlet.
DO NOT USE THE DUST FILTER FOR
LIQUID VACUUMING.
O = OFF I = ON
LIQUID VACUUM
OPERATION
LIQUID VACUUM CLEANING
WARNING: Be sure to read,
understand, and apply information, entitled
“SAFETY INSTRUCTIONS & WARNINGS”. Do not
vacuum in areas with flammable gases, vapors,
or explosive dusts in the air. Flammable gases
or vapors include but are not limited to: lighter
fluid, solvent type cleaners, oil-base paints,
gasoline, alcohol, or aerosol sprays.
Explosive
dusts include but are not limited to: coal,
magnesium, grain, or gun powder. To reduce the
risk of health hazards from vapors or dust, do
not vacuum toxic materials.
WARNING: Do not plug in power
cord to power outlet. Make sure the plug is
disconnected before changing the filters.
1.
Verify that the power cord is disconnected from
the outlet. Make sure that the collection tank is
clean and free from dust and dirt.
2.
Remove reusable cartridge filter, then carefully
install the foam sleeve filter over the filter cage
and place the power head back on the collection
tank. See filter installing instructions
DO NOT USE THE REUSABLE CARTRIDGE
FILTER FOR LIQUID VACUUMING.
OPERATING INSTRUCTIONS – WET
VACUUMING
3.
Fit the desired nozzle to the vacuum hose.
4.
Verify that the switch is in the ‘O’ OFF position
before plugging the power cord into the outlet.
5.
Turn the motor on by pressing the switch to the
‘I’ ON position.)
6.
After use, empty the container by unscrewing
the drain cap and drain liquids into suitable
receptacle or drain. Remember to refit the drain
cap to the container after draining container.
IMPORTANT: When vacuuming large quantities
of liquids, do not immerse the nozzle completely
in the liquid; leave a gap at the tip of the nozzle
opening to allow air inflow. The machine is fitted
with a float valve that stops the suction action
when the collection tank reaches its maximum
capacity. You will notice an increase in motor
speed. When this happens, turn o the machine,
disconnect from the power supply, and drain
the liquid into a suitable receptacle or drain. To
continue vacuuming, refit the collection tank
with the drain cap. After wet vacuuming, turn the
machine o and remove the plug from the power
supply. Empty the collection tank, clean and dry
the inside and outside before storage.
REMEMBER: The foam filter must be removed
after wet vacuuming, and a reusable cartridge
filter must be installed before dry vacuuming
again.
Bekijk gratis de handleiding van Dirt Devil QuickFlip SD68000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dirt Devil |
| Model | QuickFlip SD68000 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 7025 MB |
