Dexibell VIVO S2 handleiding
Handleiding
Je bekijkt pagina 24 van 84
24
Selecting Tones
The display shows a conrmation message.
The position of the sound you selected is memorized and will be
recalled every time you press the corresponding Tone button.
The instrument will remember your choice at the next power on
.
Adding the Bass Part
In addition to the Main, Coupled, and Lower parts, the instrument also
features a Bass part. To activate the Bass part, select 'BASS SETTING' in the
'SETTING GROUP' and set the 'Switch' parameter to 'ON' (p. 61).
NOTE
This part becomes monophonic when used in combination with
the Lower part. To always use this part in polyphonic mode,
set the 'Monophonic' parameter to 'OFF'. See "Monophonic" (p.
62).
1. Press [MENU/EXIT] button and select SETTINGBASS SETTING
function. See "Moving the Cursor and Setting Parameter
Values" (p. 21).
2. Use the [] [] buttons to select the 'Switch' parameter
and using the [] [] buttons set the it 'ON'.
If the Lower part is active, the Bass part is monophonic and the
leftmost note played on the keyboard is added. In all other cases
the Bass part is polyphonic.
The example below illustrates the main screen with all parts
activated.
3. To change a tone of the Bass part, see "How to Select a
Part" (p. 22).
4. Play the keyboard.
5. To adjust the overall volume use the VOLUME knob.
MEMO
To change the volume of a Bass part, you can use the 'Level' parameter
(p. 62) in the BASS SETTING group, accessible via the [MENU] button.
Alternatively, you can adjust the volume of this part in the 'VOLUME'
environment, accessed through the [VOLUME] button. For more
details, see "Adjusting the Volume for Each Part" (p. 32).
MEMO
To change the split point see "How to change the Split Point" (p. 24).
Special Pedalboard Tones: 'Pedal Bass' and
'Pedal DoubleBs'.
In the sounds set of the VIVO S2 there are two special sounds that
came in handy when you playbass note in rapid succession like
jazz. The 'Pedal Bass' and 'Pedal DoubleBs' sounds was sampled
with a little bit sustain. In this way, lengthening the release of the
sound, allows the organist to play the 'walking' bass line.
Play All Parts in Layer Mode
The VIVO S2 allows you to play the Lower and Bass in layers with the
Main and the Coupled part. To do this you need to set a parameter
in o, this parameter is called 'Split'
1. Press and hold the [ LOWER ] button until the display
shown the following page.
MEMO
You can also select this parameter pressing [MENU] button
SETTINGSPLIT MODE.
2. Use the [] [] buttons to select the 'Split' parameter.
3. Use the [] [] buttons to set the 'Split' parameter to OFF.
Parameter Setting
Split
OFF, ON
Default: ON
Now all parts will play in layers.
MEMO
To play the keyboard in split mode set again the 'SPLIT'
parameter to 'ON'.
How to change the Split Point
1. Press and hold the [ LOWER ] button until the display
shown the following page.
MEMO
You can also select this parameter pressing [MENU] button
SETTINGSPLIT MODE.
2. Use the [] [] buttons to select the 'Split Point'
parameter and use the [] [] buttons to set the new split
point or press the desiderate key on the keyboard.
Parameter Setting
Split Point
F1 ~ C#7
Bekijk gratis de handleiding van Dexibell VIVO S2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Dexibell |
| Model | VIVO S2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 17107 MB |
