DeWalt DXV20PTA-QT handleiding
Handleiding
Je bekijkt pagina 22 van 100
20
1. Make sure the control switch 3 is in the ‘Off’
position and the power supply is not connected.
2. There are 2 options for the next step.
Option 1: Connecting the tool to the vacuum rst,
then connect the power supply and turn on/off
control switch 3 to the ON position ( I ), at this
time the vacuum cleaner will start working.
Option 2: Connecting the tool to the vacuum rst,
then connect the power supply and turn on/off
control switch 3 to the ON position ( I I ), at this
time the power tool can start to use.
CONNECTING POWER TOOL (Fig. L, M)
WARNING: Use the vacuum cleaner's socket
outlet only for connection of an external power tool.
The vacuum cleaner is automatically switched on and
off via the connected power tool.
The connected load of the power tool may not exceed
the maximum connected load PA of the vacuum
cleaner’s socket outlet. Please also observe the
operating instructions and safety warnings of the
power tool being connected to the socket outlet of
the vacuum cleaner.
RECOMMENDATION: Always operate the vacuum
cleaner via a residual current device (RCD) with a rated
residual current of 200mA or less.
Please ensure that the power tool switch is in the ‘Off’
position before connecting the tool to the vacuum.
After switching off a power tool connected to the vacuum
cleaner’s socket outlet, the vacuum cleaner will run on for
approx. 15 seconds and then automatically switch off.
English
3
3
3
ELECTRICAL SAFETY
STORAGE (Fig. A)
1. Empty dust tank, refer to TO EMPTY DUST TANK
instructions.
2. Clean the vacuum inside and outside. refer
to CLEANING.
3. Clean or replace lters, refer to FILTER.
4. Store the hose and the power cord, as
shown in the Fig. A. Place the appliance in a dry
room and secure it from unauthorized use.
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. lf operating a power tool in a damp location is
unavoidable, use a residual current
device(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
MAINS PLUG REPLACEMENT
(U.K.&IRELAND ONLY)
lf a new mains plug needs to be tted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the
plug.
• Connect the blue lead to the neutral terminal.
• Connect the yellow/green lead to the earth terminal.
Follow the tting instructions supplied with good
quality plugs. Recommended fuse: 13A.
USING AN EXTENSION CABLE
lf an extension cable is required, use an approved
3-core extension cable suitable for the power input of
this tool (see Technical Data). The minimum
conductor size is 1.5 mm²; the maximum length is
30m.
When using a cable reel, always unwind the cable
completely.
7. The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
lf the supply cord is damaged, it must be replaced
only by D
EWALT or an authorised service
organisation.
WARNING: Never use a light socket. Never
connect the live (L) or neutral (N) wires to the earth
pin marked E or .
CLEANING
To keep the wet/dry vacuum looking its best, clean
the outside with a cloth dampened with warm water
and mild soap.
To clean the tank:
1. Dump out debris.
2. Wash tank thoroughly with warm water and mild
soap.
3. Wipe with dry cloth.
Bekijk gratis de handleiding van DeWalt DXV20PTA-QT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DXV20PTA-QT |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14791 MB |
