DeWalt DT70620 handleiding
Handleiding
Je bekijkt pagina 11 van 64
9
english
• Use shears upright. If tool is upside down,
metal curl may turn toward you.
• Always wear safety shoes to protect your
feet from sharp metal debris on the floor.
• Keep all screws (thumb screws) tight.
Check periodically for loosening.
• Stay clear of end pieces that may fall after
being cut off. Contact with a sharp edge
could result in personal injury.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
Package Contents
The package contains:
1 Shear Attachment
1 Instruction manual
• Check for damage to the tool, parts or
accessories which may have occurred
during transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (Fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or personal
injury could result.
A. Shank
B. Brace arm bracket
C. Thumb knob
D. Brace arm feet
E. Screw pocket
F. Swivel head adjustment knob
G. Blades
H. Blade adjustment screw
INTENDED USE
Your DT70620 shear attachment has been designed
to be used with certain cordless D
e
WALT impact
and drill/drivers, see Fits paragraph. The shear
attachment is designed to cut 1.3 mm sheet metal,
corrugated metal, duct, shingles, wire fencing,
siding, wire, plastic, cardboard and some heavy
duty rubber.
DO NOT use under wet conditions or in the
presence of flammable liquids or gases.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
FITS
D
e
WALT – DCD785, DCD790, DCF885, DCF895,
DCD995, DCD985, DCF826, DC825, DC827,
DCF886.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
Shear Assembly (Fig. 1)
1. Insert shank (A) end of shear into nose of
impact driver/drill. Tighten impact driver/drill
chuck securely.
2. Pivot brace arm bracket (B) toward rubber over-
molding at base of impact driver/drill and lock
pivot brace arm bracket into place.
3. Tighten thumb knob (C) to secure shear
attachment in place.
NOTE: Brace arm feet (D) will lock in place on
rubber over-molding or plastic and should not
pull off.
NOTE: If using an impact driver/drills without
rubber over-molding on base, place the brace
arm feet onto the plastic and lock into place.
NOTE: If using the D
e
WALT DC825 or
DC827 align spring loaded screws with screw
pocket(E).
Tighten Blades (Fig. 1)
Turn the blade adjustments screw (H) with a slotted
screwdriver to adjust the gap of the blades (G) as
needed.
Bekijk gratis de handleiding van DeWalt DT70620, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DT70620 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8950 MB |
Caratteristiche Prodotto
| Kleur van het product | Black, Yellow |
| Materiaal | Metaal |
| Constructietype | Mes met vast lemmet |
| Compatibiliteit | DeWALT |
| Type product | Universele schaaradapter |
