DeWalt DCE710 handleiding
Handleiding
Je bekijkt pagina 6 van 24
English
4
The label on your tool may include the following symbols. The
symbols and their definitions are asfollows:
V .......................... volts
Hz ........................hertz
min ...................... minutes
or DC ......direct current
....................... Class I Construction
(grounded)
…/min ..............per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM ....................
oscillations per minute
RPM ....................
revolutions per minute
sfpm ...................
surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................watts
Wh ......................watt hours
Ah ....................... amp hours
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II Construction
(double insulated)
n
o
.......................no load speed
n .........................rated speed
PSI.......................
pounds per square inch
......................earthing terminal
Additional Safety Information
WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETYEQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratoryprotection.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these
chemicalsare:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically‑treatedlumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopicparticles.
• Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmfulchemicals.
Direct particles away from face andbody.
• Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to the
operator and those in closeproximity.
• Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may lead to
loss of control andinjury.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in movingparts.
CAUTION:
When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand upright
on the battery pack but may be easily knockedover.
Warnings for Pipe Deburring Tools
a ) Always use a support device, such as a pipe stand or
vise, with the tool. Loss of control during operation can result
in personalinjury.
b ) Always hold the tool firmly when operating
to resist the reaction torque in case the support
devicemalfunctions.
c ) Keep loose clothing away while operating the tool. Do
not reach across the tool or pipe. Clothing can be caught by
the pipe or the tool resulting in entanglement.
d ) Keep long hair tied up and away from thetool.
e ) Keep floors dry and free of slippery materials such as
oil. Slippery floors inviteaccidents.
f ) When holding pipe in hand, keep hand 2" away from
tool while deburring.
g ) Always grab/hold tool using main handle only.
NEVER use the gear case to grabtool.
h ) Clear all pipes of liquid contents before using this
tool. Do not allow liquids to enter thetool.
surfaces do not allow for safe handling and control of the tool
in unexpectedsituations.
Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another
batterypack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create a
risk of injury andfire.
c ) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or afire.
d ) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause
irritation orburns.
e ) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk ofinjury.
f ) Do not expose a battery pack or tool to fire or excessive
temperature. Exposure to fire or temperature above 265°F
(130°C) may causeexplosion.
g ) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk offire.
Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool ismaintained.
b ) Never service damaged battery packs. Service of
battery packs should only be performed by the manufacturer or
authorized serviceproviders.
Bekijk gratis de handleiding van DeWalt DCE710, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | DeWalt |
| Model | DCE710 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3644 MB |
