Curtis 1220E handleiding
Handleiding
Je bekijkt pagina 16 van 72
3 — PROGRAMMABLE PARAMETERS
Curtis Model 1220E – August 2022 Return to TOC
pg. 12
3 — PROGRAMMABLE PARAMETERS
e 1220E controller has a number of parameters that can be programmed using the Curtis Integrated
Toolkit
TM
(CIT), Curtis 1313 handheld programmer or 1314 Programming Station. e programmable
parameters allow the steering performance to be customized to fit the needs of specific applications.
e programmable parameters are grouped into nested hierarchical menus, as shown in Table 1.
Table 1 Programmable Parameter Menus
COMMAND DEVICE
COMMAND INPUT DEVICE................ p. 14
SUPERVISION INPUT DEVICE............. p. 14
ABSOLUTE MODE............................ p. 14
COMMAND INPUT GAIN................... p. 14
0 - COMMAND ANALOG 1 AND 2....... p. 16
—Command Analog1 Left
—Command Analog1 Center
—Command Analog1 Right
—Command Analog1 Fault Min
—Command Analog1 Fault Max
—Command Analog2 Left
—Command Analog2 Center
—Command Analog2 Right
—Command Analog2 Fault Min
—Command Analog2 Fault Max
1 - CAN COMMAND........................ p. 17
—CAN Steer Device Type
—CAN Steer Center Offset
—CAN2 Steer Center Offset
—CAN Steer Left Stop to Center
—CAN Steer Right Stop to Center
—CAN Steer Swap Direction
—CAN2 Steer Swap Direction
2 - Command Encoder 1 and 2...... p. 18
—Left Stop to Center
—Right Stop to Center
—Left Stop to Center Supervisor
—Right Stop to Center Supervisor
—Swap Encoder1 Direction
—Swap Encoder2 Direction
—Steer Command Lead Clamp
COMMAND DEVICE, cont’d
COMMAND MAP....................................... p. 19
—Left Stop (deg)
—P1 Input
—P1 Output (deg)
—P2 Input
—P2 Output (deg)
—P3 Input
—P3 Output (deg)
—P4 Input
—P4 Output (deg)
—P5 Input
—P5 Output (deg)
—P6 Input
—P6 Output (deg)
—Right Stop (deg)
FEEDBACK DEVICE
POSITION FEEDBACK DEVICE................ p. 21
SUPERVISION FEEDBACK DEVICE............. p. 21
POSITION ANALOG 1 AND 2.................... p. 23
—Position Analog1 Left Stop
—Position Analog1 Center
—Position Analog1 Right Stop
—Position Analog1 Fault Min
—Position Analog1 Fault Max
—Position Analog2 Left Stop
—Position Analog2 Center
—Position Analog2 Right Stop
—Position Analog2 Fault Min
—Position Analog2 Fault Max
FEEDBACK DEVICE, cont’d
POSITION ENCODER 1 AND 2............. p. 24
—Encoder1 Steps
—Encoder2 Steps
—Swap Encoder1 Direction
—Swap Encoder2 Direction
—Auto Center Type
—Center Offset (deg)
—Center Compensation
HOMING.................................... p. 25
—Input Type
—Home on Interlock
—Homing Direction Method
—Homing Speed
—Homing Timeout
—Homing Compensation (deg)
VEHICLE CONFIGURATION.................. p. 26
—Nominal Voltage
—Interlock Type
—Fault Steering Timeout
—Interlock Enabled Speed
—Steering Suspension
Main Relay Driver........................... p. 27
—Main On Interlock
—Pull-In Voltage
—Holding Voltage
—Main DNC Threshold
—Open Delay
—Sequencing Delay
Bekijk gratis de handleiding van Curtis 1220E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Curtis |
| Model | 1220E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9449 MB |
