Crestron Green Light GL-EXP-DIMU-DALI handleiding

Niet gecategoriseerd

Crestron

2 pagina's

PDF beschikbaar

Handleiding

GL-EXP-DIM-DALI/GL-EXP-DIMU-DALI/GL-EXP-DIMFDB-DALI/GL-EXP-DIMFLV-DALI/GL-EXP-SW-DALI

Crestron Green Light

Expansion Module, DALI

Installation & Operation Guide

Description

The GL-EXP-DIM-DALI, GL-EXP-DIMU-DALI, GL-EXP-DIMFDB-DALI,

GL-EXP-DIMFLV-DALI, and GL-EXP-SW-DALI are independent Crestron Green Light

expansion modules that are controlled by DALI

and provide one channel of control for a

variety of lighting loads. A single module supports 120 volt or 277 volt loads up to 16

amps.

The Crestron

GL-EXP-DIM-DALI, GL-EXP-DIMU-DALI, GL-EXP-DIMFDB-DALI,

GL-EXP-DIMFLV-DALI, and GL-EXP-SW-DALI share common features and functions and

will be referred to as “GL-EXP-*-DALI” except where noted.

The specications for the GL-EXP-*-DALI are listed below.

Specications

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates.

5 13/16 in

(147 mm)

5/16 in

(9 mm)

8 5/16 in

(211 mm)

7 5/16 in

(186 mm)

8 5/8 in

(219 mm)

8 3/4 in

(223 mm)

1/2 in

(13 mm)

6 3/8 in

(163 mm)

5 1/16 in

(129 mm)

3 13/16 in

(81 mm)

2 in

(52 mm)

Typ

1 13/16 in

(46 mm)

3 1/16 in

(78 mm)

(2x) Ø3/16 in

(5 mm)

(2x)

Ø3/18 in

(10 mm)

(2x) Ø1/4 in

(7 mm)

(1 1/2 in

(39 mm)

Double Ring Knockout for 1/2 in and 3/4 in

conduit Ø.875 and Ø1.125 in after knockout

removal (typ).

GL-EXP-DIMU-DALI

2. Wire the device as shown below. An additional LINE, NEUT, and GND connection is

supplied for power to pass through. Keep the following in mind while wiring:

• Wires should be 10 to 24 AWG.

• Wires should be stripped to 5/16 in (8 mm).

• Tighten the terminal screws to 4.5 in-lbs (0.5 Nm).

Wire the GL-EXP-DIM-DALI

Wiring Diagrams

WARNING: RISK OF SERIOUS PERSONAL INJURY. Turn off power at the circuit

breaker(s) prior to installation. Installing with power on can result in serious personal

injury and damage to the device.

1. Use a #2 Phillips screwdriver to remove the cover screws and remove the cover.

Remove Cover Screws

Installation

WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker(s) or

fuse and test that power is off before wiring!

NOTES: Observe the following points:

• This product must be installed and used in accordance with the appropriate electrical

codes and regulations.

• This product must be installed by a licensed electrician.

• Use 75°C copper wire or better.

NOTE: Before using the GL-EXP-*-DALI, ensure the device is using the latest rmware.

Check for the latest rmware for the GL-EXP-*-DALI at www.crestron.com/rmware.

Firmware is loaded onto the device using Crestron Toolbox™.

Preparing and Connecting DALI and 0-10V Ports

Strip the ends of the wires approximately 7/16 in (11 mm). Use care to avoid nicking the

conductors. Tighten the connector to 5 in-lb (0.5 to 0.6 N-m). The wire gauge should be 14

to 26 AWG.

Installation

The GL-EXP-*-DALI is mounted to any vertical surface using four screws. The screws must

be appropriate for the mounting surface.

Installing the GL-EXP-*-DALI Module

NOTE: To prevent potential heat damage to the drywall, do not mount the

GL-EXP-*-DALI directly onto drywall. Mount the GL-EXP-*-DALI to a piece of plywood

that is at least 1/2 in (13 mm), and then mount the GL-EXP-*-DALI and plywood to the

drywall.

NOTE: To ensure proper ventilation, the device must be installed vertically on a vertical

surface. Install the device with 6 in (153 mm) of clearance from the top and bottom of the

device.

Mounting Surface

#8 Mounting

Screws Qty. 4

(Not Supplied)

Cover

Screws

The dimensions for the GL-EXP-*-DALI are shown in the following illustrations.

GL-EXP-*-DALI Dimensions

SPECIFICATION DETAILS

Load Ratings

Channels 1

Load Rating 16 A

Dimmed Load Types

GL-EXP-DIM-DALI:

Incandescent, magnetic low-voltage, 2-wire

dimmable uorescent

GL-EXP-DIMU-DALI:

Incandescent, electronic low-voltage, magnetic low-

voltage, 2-wire uorescent

GL-EXP-DIMFDB-DALI:

3-wire uorescent

GL-EXP-DIMFLV-DALI:

0-10 V fluorescent, 0-10 V LED

Switched Load Types

GL-EXP-SW-DALI:

Incandescent, magnetic low-voltage, electronic low-

voltage, HID, uorescent ballast

Input Voltage 100 to 277 Vac, 50/60 Hz

Indicators

PWR

Green LED indicates line power is applied to the LINE

terminal.

ON/OFF Red LED indicates power is applied to the load.

NET Yellow LED indicates network communication.

ERR Red LED blinks to indicate an error condition. Refer to

“Error States” for additional information.

FWD

(GL-EXP-DIMU-DALI

Only)

Red LED shows that the unit is operating in forward-

phase mode.

REV

(GL-EXP-DIMU-DALI

Only)

Red LED shows that the unit is operating in reverse-

phase mode.

Controls

ON/OFF Pushbutton toggles power to the load. Press and hold

the pushbutton to dim the load up and down

(dimming models only).

RESET Pushbutton initiates hardware reset.

Environmental

Temperature 32° to 104° F (0° to 40° C)

Humidity 10% to 90% RH (non-condensing)

Weight 3.4 lb (1.6 kg)

Pass Through to

Additional

Module

From Circuit

Breaker

To Dimmed

Load

From DALI

Network

To Additional

DALI Modules

Bekijk gratis de handleiding van Crestron Green Light GL-EXP-DIMU-DALI, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.