Craftsman CMCPPR320 handleiding
Handleiding
Je bekijkt pagina 9 van 32
7
English
WARNING: Always check to make sure that the sleeve
is completely threaded on and that the red threads are
no longer visible. Not threading the sleeve completely
on could result in the folding assembly becoming
disconnected creating a hazardous condition.
Periodically check the connections to ensure that no
red threads arevisible.
The three assemblies that make up the pole pruner are keyed
to ensure correct assembly. If an assembly does not smoothly
attach to another do not force fit. Combining the handle
assembly
1
, folding assembly
2
and the pruner assembly
3
creates a pole pruner that is approximately 9' (2.7m) in
length as shown in Fig. B.
1. Align the button
19
on the outside of the coupling end
of the folding assembly
2
with the button hole
20
on
the coupling end of pruner assembly
3
. Refer to Fig.C.
Push the two sections completelytogether until the
button
19
pops into the button hole
20
securing it into
position. Refer to Fig.B.
2. Align the button
21
on the outside of the coupling end
of the folding assembly
2
with the button hole
22
on
the coupling end of handle assembly
1
. Refer to Fig.D.
Push the two sections completelytogether until the
button
21
pops into the button hole
22
securing it into
position. Refer to Fig.B.
3. Straighten the folding assembly
2
together as shown
in Fig.E.
4. Slide the threaded sleeve
14
onto the folding
assembly
2
down as far as possible and rotate the
threaded sleeve
14
clockwise until it stops and
completely covers the threads as shown in Fig.F.
Transporting Pole Pruner (Fig. G)
Always remove the battery pack
16
from the handle and
cover the cutting blade
8
with the blade cover
17
when
transporting the pole pruner.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Installing and Removing the Battery Pack
(Fig. H)
WARNING: Ensure the tool/appliance is in the off
position before inserting the batterypack.
nOTE: For best results, make sure your battery pack is
fullycharged.
1. To install the battery pack
16
into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does notdisengage.
2. To remove the battery pack from the tool, press the
battery pack release button
17
and firmly pull the
battery pack out of the toolhandle.
Folding the Pole Pruner (Fig. E)
WARNING:
Sharp moving blade. To prevent accidental
operation, ensure that battery is disconnected from the
handle and that the protective blade cover is in place on the
cutting blade before performing the following operations.
Failure to do this could result in serious personal injury.
1. Rest the CMCPPR320 on the ground and grasp the
threaded sleeve
14
on the folding assembly
2
and loosen the threaded sleeve by twisting it
counterclockwise. Slide the threaded sleeve
14
away
and toward the pruner assembly
3
.
2. Fold the folding assembly
2
apart as shown in Fig.E.
On/Off Switch (Fig. I, J)
Always be sure of your footing and grip the pole pruner firmly
with both hands with the thumb and fingers encircling
the
main handle
7
and one hand on the foam gripper
13
.
1. To turn the tool ON, push the lock-off button
6
down
and then squeeze the trigger switch
5
with your fingers
as shown in Fig. J.
2. To turn the tool OFF, release thetrigger trigger switch
5
.
Proper hand position requires one hand on the main
handle
7
and one hand on the foam gripper
13
.
Proper Hand Position (Fig. I)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Pivoting the Pruner Head (Fig. A, L)
The pruner head pivots 180° and can be locked into seven
different positions within that range. Wear gloves to avoid
being pinched, do not grab the blade.
WARNING: REMOVE THE BATTERY before attempting
to pivot the pruner head. Ensure the pruner head is locked
intoposition before operating.
To Pivot the Pruner Head
1. With one hand firmly gripping the pruner head, use the
other hand to press the pivot lock button
12
and rotate
the motor housing to pivot the prunerhead.
2. Lock the pruner head into one of the seven operating
positions as shown in Fig. L. To lock the pruner head into
place, release your grip on the pivot lock button
12
.
Check to make sure that pruner head is locked into
position by trying to move the motor housing. If it is not
locked, rotate it to the nearest lockposition.
Branch Removal Hook (Fig. A)
CAUTION: The branch removal hook is not a belt hook.
Your pole pruner includes a branch removal hook
10
for the
intended purpose of helping to remove small to moderately
sized prunedbranches.
Bekijk gratis de handleiding van Craftsman CMCPPR320, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Craftsman |
| Model | CMCPPR320 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4929 MB |
