Continental PA93N-D handleiding
Handleiding
Je bekijkt pagina 5 van 32

5
OPERATIONS MANUAL      
                                REFRIGERATED BASES & PIZZA PREP TABLES
04/29/10
FIGURE 3A: Casters Must be Tight to Cabinet Bottom
Do not attempt to level casters by unscrewing them 
from the cabinet and leaving them loose, as this will 
cause damage to the cabinet and leg hole threads, 
voiding all warranties. 
IMPORTANT NOTE:  It  is  extremely  important  that  your 
cabinet is perfectly level for proper operation. If it is not 
level, the following adverse conditions may occur:
1.  The door(s) will not be properly aligned and 
     consequently will not provide a good seal. 
2.  Your unit may run excessively.
3.  An excessive amount of ice will accumulate inside 
     the cabinet, around the door opening(s) and on the 
     finned evaporator coil. If allowed to continue, ice will
     eventually block the coil and the unit will fail. This 
     can result in the loss of all food stored in the cabinet. 
4.  Defrost water will fail to drain properly and will 
     overflow the evaporator coil drain pan and into the
     cabinet of both refrigerator and freezer models.
INSTALLING LEGS AND LEVELING
If  your new  unit  is  supplied  with  adjustable  legs,  they  will  be 
packed in the accessory carton in the cabinet. Your cabinet will 
have either four (4) or (6) threaded mounting holes on the bot-
tom of the cabinet (see Figure 4). In order to install the legs, 
carefully tip the cabinet back, adding  four  (4) 2” wood  blocks 
underneath, and  simply  screw  the  threaded  leg  studs  into  the 
case bottom front leg holes. Repeat this procedure by tilting the 
cabinet in the opposite direction and install the remaining legs. 
Make  sure  the  legs  are  tightened  extremely  well  or  the  entire 
model  will  sway  or  rock  with  each  opening  or  closing  of  the 
doors, possibly causing damage to the case bottom. This pro-
cedure should be performed close to the final installation site. 
and  strong  enough  to  support  the  total  combined  weights  of 
your new model plus the maximum product load which might 
be placed into it. Keep in mind that all the weight is concentrated 
at the caster or leg locations. To estimate the possible product 
weight, assume  that  each cubic foot  of  storage space weighs 
approximately 35 pounds.  Multiply  35  pounds  by  the amount 
of cubic feet in the cabinet to obtain the product load weight. 
For example, a 20 cubic foot refrigerator can hold approximately 
700 pounds of product (35 x 20). Assuming the cabinet itself 
weighs 300 pounds, the total combined weight of cabinet and 
product is approximately 1000 pounds. Therefore, the floor in 
this example must be able to support up to 1000 pounds.
INSTALLING CASTERS AND LEVELING
If  your  new  unit  is  supplied  with  swivel  casters,  they  will  be 
packed  in  the  accessory  box  that  came  with  your  cabinet. 
Casters  should  be  installed  only  when  the  cabinet  is  close  to 
its final installation site. To install casters on your new model, 
place wooden blocks along the back, at each end. Tilt the cabi-
net back, using the wood blocks to help hold the cabinet in its 
tilted position. Locate the  large threaded  holes on the bottom 
of  the  cabinet  and  screw  the  threaded  caster  studs  into  the 
mounting  holes,  closest  to  the  front  of  the  unit.  Repeat  this 
procedure  by  tilting  the  cabinet  in  the  opposite  direction  and 
installing  the  remaining  casters.  Make  sure  the  casters  are 
tightened extremely well (see Figure 3 & 3A). If the casters are 
not installed tightly, the cabinet will be unstable and may sway 
or rock, which can damage the cabinet. 
If  the  height  of  a  caster  needs  to  be  raised,  shims  must  be 
installed  under  the  casters  which  need  leveling.  Extra  large 
washers, available at most hardware or furniture stores, can be 
used to shim casters, or contact the factory for caster shims.
A
OPTIONAL
CASTER SHIM
(CM1-2476)
CASTER
CASTER INSTALLATION
BLOCKS
FIGURE 3: Installing Casters
Bekijk gratis de handleiding van Continental PA93N-D, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Continental | 
| Model | PA93N-D | 
| Categorie | Niet gecategoriseerd | 
| Taal | Nederlands | 
| Grootte | 5803 MB | 




