Concept RoboCross VR3300 handleiding
Handleiding
Je bekijkt pagina 42 van 79
EN EN
82 83
The planned cleaning did
not take place
If the battery level is low, planned cleaning can only be started if the battery level is
at least 30 %.
Does the robot consume
power when it is always
placed in the docking
station?
The robot consumes a small amount of power when it is permanently placed in the
docking station, allowing the best battery performance.
Does the robot need to
be charged for 16 hours
for the first 3 uses?
The lithium battery can be used immediately after charging and has no memory effect.
TROUBLESHOOTING
Voice message Problem
Error 1: Oh dear! I cannot find the dust collector Cleaning was started after removing the dust container.
Insert the container.
Error 2: Please check if the radar on top has been covered
or blocked
The top sensor is covered or placed in an open area
(there is no obstruction in the 6x6 m
2
area).
Error 3: Please place me in a new location and try again Pick up the robot or lift it into the air.
Error 4: Please scrub the cliff sensor, and restart me from
a new location
The cliff sensor is covered or placed at a height.
Error 5: Please scrub the front sensor, and restart me
from a new location
The infra-red anti-collision sensor is dirty or covered.
Error 6: Please scrub the right-hand sensor, and restart
me from a new location
The side sensor is dirty or obstructed.
Error 7: Please scrub the radar housing on top, and
restart me from a new location
The anti-collision radar sensor is dirty or covered.
Error 8: Please check if the bumper has been blocked in
some way
The edge sensor or anti-collision sensor is stuck.
Error 9: Master, please clean the dust container and filter The dust container is full or the filter needs to be
replaced.
Error 10: Dust container has been removed, please clean
the container and filter
After error 9 has been signalled, the user has removed
the dust container and this triggers error 10.
Error 11: I'm stuck, please help me! The robot is stuck somewhere.
Error 12: Please place me correctly! The robot is tilted.
Error 13: Please check if my wheels have become blocked
somewhere
The drive wheel is stuck or tangled.
Error 14: Please check if the main brush has become
stuck
The main brush is tangled or stuck.
Error 15: Please check if the side brushes have become
stuck
The side brush is tangled or stuck.
Error 16: What's going on? Where is the docking station? Docking station not found or not connected.
Error 17: Oh dear! Program error, please restart me Abnormal condition due to unknown failure, restart the
robot.
Error 18: Error encountered initiating shutdown The robot alerts the user and automatically shuts down
or recharges.
Error 19: Low battery, please recharge When the battery charge level is too low, the robot is not
in the docking station and cleaning starts (the battery
charge level is less than 10 %).
Error 20: To shut me down, please place me away from
the docking station
To turn off the robot, move it from the docking station.
Error 21: Collecting fan motor error Try reconnecting the charging cable, if the problem
persists, contact the service department.
WIRELESS CONNECTION AND COMPATIBILITY
• Jindřich Valenta - CONCEPT shall in no way be liable for any incidental, indirect or consequential damages, or for any
loss of data or loss due to information leakage during communication via wireless technology.
• Successful wireless communication cannot be 100% guaranteed on all Smart devices and Wi-Fi networks (routers).
Due to the variety of devices on the market, there may be cases where the character or specification of a given Smart
device or Wi-Fi network (router) makes connection impossible or is somehow disturbed. In addition, a number
of factors, including hardware and software configuration, also affect the success of wireless communication via
Wi-Fi network. The connection between the robot and your Wi-Fi network can also be adversely affected by the
surrounding Wi-Fi networks, which can be tuned to the same channel and thus interfere with the connection (e.g.
in housing estates, apartment buildings, etc.). These facts are not a reason to claim the appliance.
• The app is owned and operated by a third party (the “Entity”) different from Jindřich Valenta - CONCEPT (the
“Seller”). No personal data is transferred to the Entity by the Seller. When registering for the app, the customer
submits personal data directly to the Entity, who becomes the administrator of personal data. The app and the
associated protection of personal data are governed by the Entity’s rules.
Compatibility:
Smart device operating system - Android 5.0 and higher
- IOS 9.0 and higher
Wi-Fi network - 2.4 GHz
- WPA1 and WPA2 security (WPA2 recommended)
NOTICE: The appliance cannot be operated on IEEE 802.1X-protected Wi-Fi networks (usually corporate Wi-Fi networks).
OPERATING USING THE APP
Before you can control the device using the app, it is necessary to connect it to your phone and give it access to your
Wi-Fi network.
Recommended distance during set-up: less than 4 meters.
Make sure your robotic vacuum cleaner, router, and your mobile phone are close together so that you can pair your phone
with the device with no problems.
Bekijk gratis de handleiding van Concept RoboCross VR3300, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Concept |
| Model | RoboCross VR3300 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 11701 MB |
