Cicada Audio CH65.4V2 handleiding
Handleiding
Je bekijkt pagina 7 van 18
SYSTEM DESIGN - PASSIVE / ACTIVE
TYPICAL “BI-AMPED” SYSTEM USING
PASSIVE CROSSOVERS
The Cicada Audio CH COAX HORN comes with a special
12dB per octave crossover. It is HIGHLYrecommended
CH SERIES COAX TWEETER
that this be used at ALL times - UNLESS you are using
+
12dB PER OCTAVE
HIGH-PASS FILTER
an active crosssover set at above 4kHz. Like our
(INCLUDED)
DSP125.4D amplifier or our DSP88 stand alonee processor
+
with amplifiers. This system, shown is “Bi-Amped”, but not
‘Fully” active. FRONT channels of this 4 channel amplifier
are driving the mid bass drivers. REAR channel are
driving the tweeters. The MIDBASS is shown with a
0.16mH inductor (not included) in series to cross
over the midbass at 4Khz with a 6dB roll-off.
0.16mH INDUCTOR
(NOT INCLUDED)
+
“OPTIONAL”
TWEETER ATTENUATION
NOTE: This setup makes it easier to adjust
level of the midbass versus the tweeter
CH1(FL -) CH1(FL +)
by simply adjusting the levels of each
CH1 CH2 +
CH3 CH4 +
+12V REM GND
channnel. Piece of cake!!!
PWR
PRT
CH1 + CH2 CH3+ CH4
BRIDGED
BRIDGED
SPEAKER OUTPUT
IF you USE a DSP you dont
need the additional low
CH3(RL -) CH3(RL +)
pass filter(inductor) as shown
4 Ohm resistor
INCLUDED
TYPICAL “FULLY ACTIVE” SYSTEM
CH SERIES COAX HORN SPEAKER
RUNNING ALL ACTIVE 12dB SLOPES @ 4KHz
CH series COAX HORN drivers can be “Bi-Amped” Or what is
HIGH AND LOW PASS FILTER(THRU DSP)
+
commonly called FULLY active system setup. In the system shown
- the tweeter(s) are wired to the FRONT channels and the MIDBASS
CH SERIES HORN TWEETER
12dB HIGH-PASS @ 4KHz
driver section is wired to the rear channels. At this point you should
seriously think about purchasing a DSP processor - unless your
amplifier has a HP filter that can go to 4Khz, like our CIcada DSP125.4D
DSP Amplifier. (which has infinite filter and slope configurations!!)
Using a DSP amp/processor (or DSP processor and any amplifier)
makes it much easier to control and tune your system.
We recommend using our amplifier with built
in DSP (DSP125.4D)or a stand alone DSP like
our DSP88 Small 8 in 8 out, simple to use....and
controlled by your SmartPhone..or PC.
CH MIDBASS -12dB LOW-PASS @ 4KHz
CH1(FL -) CH1(FL +)
CH1 CH2 +
CH3 CH4 +
+12V REM GND
PWR
PRT
DSP88
CH1 + CH2 CH3+ CH4
BRIDGED
BRIDGED
SPEAKER OUTPUT
CH3(RL -) CH3(RL +)
2021 Cicada Audio All rights reserved.
6
Bekijk gratis de handleiding van Cicada Audio CH65.4V2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Cicada Audio |
| Model | CH65.4V2 |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 11244 MB |
