Cecotec Bolero Squad I 2100 Flex handleiding

Fornuis

Cecotec

117 pagina's

PDF beschikbaar

Handleiding

Bolero Squad I 2100 FlexBolero Squad I 2100 Flex

6968

ENGLISH ENGLISH

Fig. 8 key:

1. Induction hob

2. Bracket

3. Worktop

Warning:

Brackets should not, under any circumstance, touch the interior surfaces of the worktop after

installation. Fig. 8

Caution:

- It is recommended that qualied personnel or technicians install the hob. You should not

install it on your own.

- Do not install the induction hob directly over a dishwasher, a refrigerator, a freezer, a

washing machine, or a dryer, as moisture could damage the electric system of the hob.

- The induction hob must be installed in a manner that ensures the best heat radiation to

obtain the best results.

- The wall and the area over the work surface must be heat resistant.

- To avoid any damage and ensure a correct xing of the hob, we recommend sealing the

latter using a sealing gasket or heat-resistant adhesive.

- You should not use steam cleaners.

Connecting the induction hob to the mains

- The induction hob must be connected to the mains by a suitably qualied person.

- Before connecting the hob to the power supply line, check that:

1. The domestic electrical installation is suitable for the power consumed by the induction

hob.

2. The mains voltage matches the voltage stated on the rating label of the appliance.

- The power cord supplied with the hob is sized to withstand the specic load indicated on

the product label.

- To connect the hob to the mains, do not use adapters, reducers, or branching devices, as

they may cause overheating or re.

- The power cord should not be in contact with any hot parts and must be positioned so as

to avoid its temperature exceeding 75 °C.

Warning

- Check with an electrician whether your home wiring system is suitable without modifying

it.

- Any modications should only be carried out by a qualied electrician.

- The power supply must be connected in accordance with the relevant regulations. The

connection method is shown in Figure 9.

screws, at a minimum distance of 50 mm from the bottom of the induction hob. Follow the

indications in Figure 6.

Warning

- There are ventilation holes around the outside of the induction hob. You must ensure these

gaps are not blocked by the worktop when installing the hob.

- Please note that the glue that binds the plastic or wooden material to the furniture must

withstand a temperature of more than 150ºC to prevent the coating from peeling o.

- The rear wall and the adjacent and surrounding surfaces must be able to withstand a

temperature of 90ºC.

Before installing the hob

- Make sure the counter in which you install the hob is levelled, complies with the space

requirements, and is made of a heat-resistant and insulated material.

- If you install the induction hob over an oven, the latter must have a cooling fan.

- The installation must comply with all the safety requirements and the applicable rules and

regulations.

- The main wiring is tted with a suitable isolating switch that allows complete disconnection

from the mains, which has been installed and positioned in accordance with local wiring

rules and regulations.

- The isolating switch must be of an approved model and provide 3 mm contact separation

on all poles (or on all active [phase] conductors if local wiring regulations allow this

variation of requirements).

- If in doubt about the installation, seek advice from local building authorities and regulations.

- Use heat-resistant and easy-to-clean nishes (such as ceramic tiles) on the walls

surrounding the hob.

After installing the hob

- The power cord should not be accessible through the cabinet doors or drawers.

- Make sure that there is an adequate ow of fresh air from the exterior of the cabinet to

the hob base.

- If the hob is installed above drawers or cabinets, you must install a thermal protection

barrier under the hob base.

- The user must be able to access the isolating switch easily.

Fixing brackets

- You must place the hob on a stable and smooth surface (you can use the packaging). Do

not apply force to the hob.

- Screw the four brackets to the bottom of the hob, then install the latter in the worktop

recess (as shown in Figure 7).

- Adjust the bracket position to the thickness of the worktop. Fig. 8

Bekijk gratis de handleiding van Cecotec Bolero Squad I 2100 Flex, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.