Cecotec Bolero Flux TLM 606500 handleiding

Afzuigkap

Cecotec

68 pagina's

PDF beschikbaar

Handleiding

BOLERO FLUX TLM 603500 WHITE A / BOLERO FLUX TLM 603500 BLACK A/

BOLERO FLUX TLM 603500 INOX A/ BOLERO FLUX TLM 606500 INOX A

BOLERO FLUX TLM 603500 WHITE A / BOLERO FLUX TLM 603500 BLACK A/

BOLERO FLUX TLM 603500 INOX A/ BOLERO FLUX TLM 606500 INOX A

5554

ENGLISH ENGLISH

- To remove the lter, press on the tabs as shown in Figure 9 and pull it out.

Carbon lter

This type of lter has activated carbon and puries air and absorbs cooking odours. The

activated carbon becomes saturated after a period of time, which will reduce the adsorption

capacity of the lter. The carbon lter cannot be washed nor cleaned in any way. When its

service life comes to an end you must replace it with a new one.

- It is recommended to check the condition of carbon lters regularly, at least two or three

times a year. Its replacement will depend on how the kitchen hood is used, as well as the

daily operating time.

- In case of very frequent frying, shorten the time interval for checking and/or replacing the

carbon lters.

Installing the carbon lters

1. Remove the protective metal lters.

2. The carbon lters are located on both sides of the motor. Insert and turn the lters, until

they are rmly in place.

3. To replace the carbon lter, proceed in reverse order.

4. The carbon lter must not be exposed to heat.

Fig. 2 10:

A: Closed

B: Opened

C: Opened

D: Closed

Carbon lter diameter:

Article No 02859/02860/02861 > 132 mm

Article No 02862 > 176 mm

Replacing the light bulb/lamp

Please note:

- The light bulb must be replaced by the ocial Cecotec Technical Support Service or

similarly qualied technicians.

- Always disconnect the power supply before performing any operation on the appliance.

When handling the bulb, make sure that it has cooled down completely before any direct

contact with your hands.

- When handling the bulbs, hold them with a cloth or gloves to prevent sweat from coming

into contact with the bulb, as this may reduce the bulb life.

Note:

- Before changing the light bulb, make sure that the appliance is switched o and unplugged.

- Protect yourself from danger when changing the light bulb, e.g., by wearing gloves.

6. TROUBLESHOOTING

Fault Cause Solution

The indicator light is

on, but the motor does

not work

The kitchen hood is

obstructed

Remove what is obstructing the

hood

The condenser is damaged Please contact the ocial Cecotec

Technical Support Service to

replace the condenser.

Motor is jammed or bearing

damaged

Please contact the ocial Cecotec

Technical Support Service to

replace the motor.

Motor is burnt or gives o a

bad smell

Please contact the ocial Cecotec

Technical Support Service to

replace the motor.

Neither the light bulb

nor the motor work

In addition to the above, check the following:

The light bulb has blown Please contact the ocial Cecotec

Technical Support Service to

replace the light bulb.

Power cable is loose Please contact the ocial Cecotec

Technical Support Service to

connect the cables according to the

wiring diagram.

Grease falls out of the

aluminium lters

The lters are very dirty Clean or replace the aluminium

lters immediately

The kitchen hood

vibrates

The fan is damaged, causing

the kitchen hood to vibrate

when extracting air.

Please contact the ocial Cecotec

Technical Support Service to

replace the fan.

The engine is not securely

fastened

Fix the engine correctly

The kitchen hood is not

securely fastened

Fix the kitchen hood correctly

Bekijk gratis de handleiding van Cecotec Bolero Flux TLM 606500, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.