Cecotec Bolero Flux DT 908010 handleiding

Afzuigkap

Cecotec

77 pagina's

PDF beschikbaar

Handleiding

BOLERO FLUX DT 608010 GLASS BLACK A++/WHITE A++

BOLERO FLUX DT 908010 GLASS BLACK A++/WHITE A++

BOLERO FLUX DT 608010 GLASS BLACK A++/WHITE A++

BOLERO FLUX DT 908010 GLASS BLACK A++/WHITE A++

5756

ENGLISH ENGLISH

Replacing the light bulb/lamp

Please note:

- The light bulb must be replaced by the ocial Cecotec Technical Support Service or

similarly qualied technicians.

- Always disconnect the power supply before performing any operation on the appliance.

When handling the bulb, make sure that it has cooled down completely before any direct

contact with your hands.

- When handling the bulbs, hold them with a cloth or gloves to prevent sweat from coming

into contact with the bulb, as this may reduce the bulb life.

Note:

- Before changing the light bulb, make sure that the appliance is switched o and

unplugged.

- Protect yourself from danger when changing the light bulb, e.g. by wearing gloves.

6. TROUBLESHOOTING

Fault Cause Solution

The indicator light

is on, but the motor

does not work

The kitchen hood is

obstructed.

Remove what is obstructing the hood.

The condenser is damaged. Please contact the ocial Cecotec

Technical Support Service to replace

the condenser.

Motor is jammed or bearing

damaged.

Please contact the ocial Cecotec

Technical Support Service to replace

the motor.

Motor is burnt or gives o a

bad smell.

Please contact the ocial Cecotec

Technical Support Service to replace

the motor.

Neither the light bulb

nor the motor work

In addition to the above, check the following:

The light bulb has blown. Please contact the ocial Cecotec

Technical Support Service to replace

the light bulb.

Power cable is loose. Please contact the ocial Cecotec

Technical Support Service to connect

the cables according to the wiring

diagram.

Cleaning the lters

Do not use corrosive detergents to clean grease from the mesh lters. Regular cleaning of

the lters will prolong the life of the appliance and keep it in good working order. Follow the

instructions below:

- Cleaning method 1: immerse the mesh lters in hot water (40-50 °C), add neutral

detergent and let them soak for 2 to 3 minutes. Protect yourself with gloves and clean the

lters with a soft brush or scouring pad. Do not apply too much force, as lters are very

delicate and can be easily damaged.

- Cleaning method 2: if you wish, you can also wash the lters in the dishwasher at a

temperature of approx. 60 °C.

- To remove the lter, press on the tabs as shown in Figure 10 and pull it out.

Carbon lter

This type of lter has activated carbon and puries air and absorbs cooking odours. The

activated carbon becomes saturated after a period of time, which will reduce the adsorption

capacity of the lter. The carbon lter cannot be washed nor cleaned in any way. When its

service life comes to an end you must replace it with a new one.

- It is recommended to check the condition of carbon lters regularly, at least two or three

times a year. Its replacement will depend on how the kitchen hood is used, as well as the

daily operating time.

- In case of very frequent frying, shorten the time interval for checking and/or replacing the

carbon lters.

Installing the carbon lters

1. Remove the protective metal lters.

2. The carbon lters are located on both sides of the motor. Insert and turn the lters, until

they are rmly in place.

3. To replace the carbon lters, proceed in reverse order.

4. Carbon lters must not be exposed to heat.

Figure 11:

A: Closed

B: Opened

C: Opened

D: Closed

Carbon lter size > Φ176 x 35 mm

Bekijk gratis de handleiding van Cecotec Bolero Flux DT 908010, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.