Cecotec Bolero DressCode 6150 handleiding

Wasmachine

Cecotec

215 pagina's

PDF beschikbaar

Handleiding

/ 215

Je bekijkt pagina 63 van 215

BOLERO DRESSCODE 6150 INVERTER A

BOLERO DRESSCODE 7150 INVERTER A

BOLERO DRESSCODE 7150 INVERTER STEEL A

BOLERO DRESSCODE 6150 INVERTER A

BOLERO DRESSCODE 7150 INVERTER A

BOLERO DRESSCODE 7150 INVERTER STEEL A

125124

ENGLISH ENGLISH

6. TROUBLESHOOTING

Non-faulty conditions

The door cannot be opened

- Programme is running.

- There is clothing between the door and the door seal.

A slight odour is produced

There may be a rubber odour from some components, the odour will disappear with use.

It is recommended to leave the door ajar after each wash until the inside of the drum is

completely dry, this will prevent odours and the formation of mould.

There is too little water when washing and rinsing

The washing machine only needs a little water during operation.

No water inlet

- Is the water supply tap open?

- Is the inlet hose frozen?

- Are the lters blocked or dirty?

- Is there sucient water pressure?

Water inlet at half

If the water level is low, the appliance will automatically supply water.

Water comes out when washing

Check if you added detergent with too much foam or too much quantity.

Remaining time change

If the laundry is not evenly placed inside the drum when spinning, the spin time will be

increased, in order to even out the imbalance and correct the deviation.

There is an abnormal noise when spinning

Have the transport bolts been removed?

Are there pieces of metal or coins in the drum?

Washing machine cannot work after a power failure

The washing machine will stop working after a power failure. When power is restored, for

safety reasons, it will not start up. Press the power button and restart the programme.

Fig. 17 key:

1. Water inlet valve

In case of freezing

1. Cover the tap and the coupling device with a hot towel.

2. Remove the inlet hose and place it in 50 degree water.

3. Pour approximately 2 - 3 l of water at 50 degrees into the drum.

4. Connect the inlet hose, open the tap and switch on the washing machine, check if the inlet

and outlet are normal.

Fig. 18 key:

a.-

1. Tap

2. Connection pipe

3. Inlet tube

b.- Remove the inlet tube and place it in water at 50 ºC.

4. Water at 50 ºC

c.- Pour approximately 2 - 3 l of water at 50 ºC into the drum.

5. Water at 50 ºC

Cleaning of the drain pump lter (Suggestion: once a month)

1. Press the lock on the pump after draining (with the washing machine switched o), open

the water pump lter cover. (Attention: if there is hot water inside, wait for it to cool down).

2. Remove the lter counterclockwise.

3. Wash the lter.

4. Go to the pump and insert the lter, tighten it clockwise and tighten the cap.

Warning:

a. Secure the lter tightly to prevent leakage.

b. Do not clean during operation.

NOTE: use extreme caution as spillage may occur. Use a container to collect the water.

Drum cleaning (Suggestion: one a month)

After use over a period of time, some dirt may remain. You can clean the inside and outside of

the drum using the Drum Cleaning programme.

Caution: do not insert laundry nor detergent/softener when using this function.

/ 215

Bekijk gratis de handleiding van Cecotec Bolero DressCode 6150, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.