Cecotec Bolero Aguazero 6700 B handleiding

Vaatwasser

Cecotec

119 pagina's

PDF beschikbaar

Handleiding

Bolero Aguazero 6700 B

Bolero Aguazero 6700 Inox B

Bolero Aguazero 6700 Dark B

Bolero Aguazero 6700 B

Bolero Aguazero 6700 Inox B

Bolero Aguazero 6700 Dark B

6968

ENGLISH ENGLISH

- If the hardness of the tap water exceeds a certain level, it must be softened, i.e. decalcied,

by adding salt to the water softener system inside the dishwasher. The amount of salt

required is adjusted according to the hardness of the tap water.

ATTENTION:

- Only use salt special for dishwashers. Any other type of salt not specically designed for

dishwasher use, especially table salt, will damage the water softener. In case of damage

caused by the use of unsuitable salt, Cecotec does not give any guarantee and is not liable

for any damage caused.

- Only add salt just before starting one of the full washing programmes. This will prevent

salt grains or salt water, which may have spilled, from remaining in the bottom of the

machine for a certain period of time, which could cause corrosion.

Check water hardness

1. Check the water hardness in your area. You can contact your water supply company to get

this information.

2. Adjust the water softener according to the hardness level of the water supplied.

Adjustment of the descaling system

Adjust the descaler according to the hardness level of the water supplied. The descaling

system has 9 levels of adjustment. The dishwasher has been set to water hardness level H5

when leaving the factory.

Settings for 15 place settings

- Make sure that the dishwasher is switched o and press the Dual Zone icon for 3 seconds

to set the programme.

- Press the Dual Zone icon. The current conguration will be displayed.

- Press the Turbo Dry+ function icon and select the desired value. The range of values that

can be selected is from H0 to H8.

- Once the necessary settings have been made, press the Power icon to switch o the

dishwasher and save the settings.

Adding salt

Warning:

- The salt tank of the dishwasher must be full before starting the washing programme. If

there is not enough salt, the corresponding indicator light will light up, unless the hardness

level is set to H0.

- After lling the salt tank, it is recommended to start a washing programme immediately.

This will remove the salt accumulated around the inner cylinder and prevent corrosion.

2. Check the detergent

Add the recommended amount of detergent into the dispenser and close the door. If you need

to prewash the tableware, the slot at the top of the door should also be lled with detergent.

3. Close the door

4. Switch on the dishwasher

Press the Power icon to switch the appliance on and o.

5. Check the rinse aid

If the rinse aid level is low, the rinse aid indicator light will ash.

IMPORTANT: always add rinse aid to improve the drying process.

6. Select the desired programme and options

See the programme guide in this manual. The display will show the estimated programme time

and the selected option.

7. Start the dishwasher

First, close the door. Then, press the Start/pause icon . If you open the door while the

programme is in operation, the dishwasher will stop. When you close the door, the programme

will resume.

8. End of programme

When the washing programme is nished, the appliance will beep, and the dishwasher will

switch o automatically after a few minutes.

Warning:

Do not open the door during operation or immediately after the end of the washing programme,

as steam build-up may cause burns.

Tips:

- You can rst remove the tableware from the bottom basket and then from the upper basket.

Doing so will prevent water from dripping from the upper basket onto the tableware in the

bottom basket.

- To save energy and water, try to maximise the capacity of the baskets.

Before use

Soft water system

- This dishwasher is equipped with a soft water system (salt tank). Its mission is to soften,

to a certain extent, the hardness of the water used and thus optimise the dishwashing

result.

- If the water in your area does not need to be descaled (low hardness), the dishwasher can

be used without dishwasher salt, but it is necessary to set the hardness level to H0 so that

the corresponding indicator light is not lit all the time.

- To achieve an optimal washing eect, the dishwasher needs soft water, otherwise water

spots will remain on the tableware and inside the dishwasher. Hard water can also produce

limescale deposits in the dishwasher and cutlery.

Bekijk gratis de handleiding van Cecotec Bolero Aguazero 6700 B, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.