Carel pCO5 handleiding
Handleiding
Je bekijkt pagina 7 van 48
7
ENG
pCO5plus +0300020EN rel. 1.9 - 28.03.2025
1. INTRODUCTION
The pCO5+ is a microprocessor-based, programmable electronic
controller that is fully compatible (hardware and software) with the pCO
Sistema family of devices, which includes programmable controllers, user
terminals, gateways, communication devices and remote management
devices. These devices represent a powerful control system that can
be easily interfaced with most Building Management Systems (BMS)
available on the market.
The pCO5+ controller has been developed by CAREL to provide solutions
to a host of applications in air-conditioning, refrigeration and HVAC/R in
general. It is highly exible and can be used to make special products on
customer speci cations.
In a pLAN network (pCO Local Area Network) the pCO5+ can be connected
to input/output expansion cards (e.g. pCOe), to other pCO5+ controllers,
to all the controllers of the pCO Sistema family and to the terminals of the
pGD range. Up to 32 devices (controllers and terminals) can be connected
together, allowing highly e cient sharing of information. Each device in
the pLAN network can exchange digital or analogue data with all the
others, depending on the application program used.
Compared to pCO3 controllers, pCO5+ units are equipped with two extra
built-in RS485 serial ports – one for the Fieldbus and one for supervision/
telemaintenance purposes (BMS).
Each Fieldbus serial port, whether built into the controller or installed via
an optional card, can be connected to controlled eld devices such as
valve and damper actuators and external drivers (e.g. drivers for electronic
expansion valves, EVD Evolution).
Each BMS serial port, whether built into the controller or installed via
an optional card, can be connected to eld-level, automation-level or
management-level standard bus systems, such as KNX®, LON®, BACnet™,
etc.
The Medium range includes controller versions with one or two built-in
drivers for electronic expansion valves. The Ultracap module (accessory)
can be used as an emergency power supply for valve drivers, and allows
shutting the valves completely in case of power failures (alternating
current).
Main features
• the same controller can be connected to up to 3 PGN terminals (semi-
graphic terminals such as pGN or touch screens such as pGDx);
• the program and parameters are saved permanently in a non-volatile
memory ( ash memory), preventing data loss in case of power failures
(without requiring a backup battery);
• 32-bit microprocessor controllers with 5 or 9 MB storage capacity
ensure high performance in terms of speed and memory space;
• allows connecting up to 32 devices to pLAN networks consisting
of a series of pCO5+ controllers and terminals. Each controller can
exchange data with the other controllers at high speed without
requiring additional hardware;
• external or built-in terminal with display and LED-button keypad; can
be used for uploading software and commissioning;
• fast upload/download of controller software using a “smartkey (*)” or any
pendrive (provided the controller is equipped with the relative port);
• universal inputs/outputs con gurable via an application program for
connecting active and passive probes, digital inputs, analogue and
PWM outputs. This extends the possibilities of con guring inputs/
outputs without having to install a larger controller;
• allows using the software 1tool or STone, installed for creating
and customising application programs, performing simulations,
supervising operations and setting up pLAN networks;
• allows uploading application software to the controller using the
command line tool/commissioning tool, available free of charge at
http://ksa.carel.com;
• many dedicated programs available for controlling a variety of HVAC/R
applications;
• allows developing new application programs according to customer
speci cations;
• wide range of models distinguished by:
- microprocessor storage capacity: 5 or 9 MB;
- size (Small, Medium, Large, Extralarge), for maximum exibility
depending on the application;
- solid state relay (SSR) digital outputs (24/230 V);
- NO or NC relay outputs;
- USB ports;
- optically-isolated/non-optically-isolated built-in serial ports;
- built-in display.
• various kinds of connectors (spring, screw, etc.).
(*) function available from smartkey rmware version 4.0.
pCO5+ HS uses a high-performance CPU.
This means faster boot times, and signi cantly faster data transfer rates.
The pCO5+ HS models are fully backward compatible with the standard
pCO5+ models.
Main features of terminal
Thanks to the capabilities of the application software, while the unit is
normally working the user terminal can be used to:
• edit the main parameters;
• receive acoustic alerts (from buzzer) and visual alerts (on display) of any
alarms triggered;
• view active functions and measured quantities displayed by LED
indicators.
1.1 Models and options
1tool
A development environment designed as a set of independent atoms,
macroblocks and modules, 1tool allows a designer to manage the
software application in all its various phases: from design, to testing and
debugging up to the eld commissioning phase. A main characteristic
of the tool is integration, as all environments share the information
necessary to best support the development of the software application.
Furthermore, the use of 1tool guarantees the customer the
maximum con dentiality and self-management to develop programs
independently. The possibility of using the same hardware in di erent
applications guarantees standardization with the well-known advantages
of planning in-circuit, functional and burn-in test procedures on the
entire production and therefore obtaining a high degree of reliability at a
global level and for each individual electronic component.
Development environment:
• 1tool: environment where expert algorithm programmers prepare the
heart of the application program.
Programming environment features:
- software transferability on di erent hardware. Applications
developed for pCO can be transferred simply and quickly from one
hardware platform to another and vice versa, simply by adapting the
inputs and outputs;
- rapid creation, at a competitive cost, of customized programs;
- reliability guaranteed by the use of standard routines tested in the
laboratory and in the eld.
Command line tool:
• EasyWinload: it is intended to program the control by loading the
application program and the appropriate con guration of the machine
during assembly.
Commissioning tool:
• pCOManager: see 1tool Appendix (+030220886) in KSA ->
Sw&Support -> 1tool --> Documents.
Bekijk gratis de handleiding van Carel pCO5, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Carel |
| Model | pCO5 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10234 MB |
