Handleiding
Je bekijkt pagina 14 van 16
Instruction manual C817C Instruction manual C817C
26 27
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
CONNECTING THE HOB TO THE MAINS POWER SUPPLY
WARNING:
The power supply should be connected in compliance with the relevant standard,or a single-pole
circuit breaker. The method of connection is shown below.
› If the cable is damaged or needs replacing, this should be done by an after-sales technician
using the correct tools.
› If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker
must be installed with a minimum gap of 3mm between the contacts.
› The installer must ensure that the correct electrical connection has been made and that it
complies with safety regulations.
› The cable must not be bent or compressed.
› The cable must be checked regularly and replaced by authorised technicians only.
Under any circumstances, the brackets cannot touch with the inner surfaces of the worktop after installation (see picture). This will
ensure the hob is properly secured to the underside of the work surface.
The bottom surface and the power cord of the hob are not accessible after installation.
CLEANING AND MAINTENANCE
WHAT? HOW? IMPORTANT
Everyday soiling on
glass [ngerprints,
marks, stains left by
food or non-sugary
spillovers on the glass].
1. Switch the power to the hob off.
2. Apply a hob cleaner while the glass is still
warm [but not hot!].
3. Rinse and wipe dry with a clean cloth or
paper towel.
4. Switch the power to the hob back on.
- When the power to the hob is switched off,
there will be no “hot surface” indication
but the cooking zone may still be hot! Take
extreme care.
- Heavy-duty scourers, some nylon scourers and
harsh/abrasive cleaning agents may scratch
the glass. Always read the label to check
whether your cleaner or scourer is suitable.
- Never leave cleaning residue on the hob as
the glass may become stained.
Boilovers, melts, and
hot sugary spills on
the glass.
Remove these immediately with a sh slice,
palette knife or razor blade scraper suitable
for ceramic glass hobs, but beware of hot
cooking zone surfaces:
1. Switch the power to the hob off at
the wall.
2. Hold the blade or utensil at a 30° angle
and scrape the soiling or spill over to a
cool area of the hob.
3. Clean the soiling or spill up with a dish
cloth or paper towel.
4. Follow steps 2 to 4 for ‘Everyday soiling
on glass’ above.
Remove melts and sugary food
or spillovers as soon as possible.
If left to cool on the glass, they may be difcult
to remove or may even permanently damage
the glass surface.
Cut hazard: when the safety cover is retracted,
the blade in a scraper is razor-sharp. Use with
extreme care and always store safely and out
of reach of children.
Spillovers on the
touch controls.
1. Switch the power to the hob off.
2. Soak up the spill.
3. Wipe the touch control area with a clean,
damp sponge or cloth.
4. Wipe the area completely dry with a
paper towel.
5. Switch the power back on.
The hob may beep and turn itself off, and the
touch controls may not function while there
is liquid on them. Make sure you wipe the
touch control area dry before turning the hob
back on.
Bekijk gratis de handleiding van Caple C817C, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Caple |
| Model | C817C |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 1219 MB |
