Candy BC448M4D8J-S handleiding
Handleiding
Je bekijkt pagina 19 van 148
A
B
C
6
2
3
B
A
4
B
A
5
A
A
A
A
B
B
B
1
19
Download the hOn App
EN
Built-in washing machine
THANK YOU FOR PURCHASING A CANDY PRODUCT
Before using the appliance, carefully read the safety instructions.
Before using the machine, it is absolutely necessary to remove the
screws and transport lock spacers.
For detailed instructions on the removal procedure, see the Installation
Instructions.
Download and read the complete User Manual online for more details.
1. Installation
1.1 - Transportation bolts removal
• Remove the 2 or 4 transportation screws (A) and the at washers, rubber bungs
and plastic spacer tubes (B) as shown in �gure 1.
•
If spacer tubes fall inside the machine, tilt it forward to retrieve them from the
oor or the base.
• Cover the screw holes with the 2 or 4 plastic caps provided.
Keep packaging materials away from children.
1.2 - Hydraulic connections
•
The machine should be connected to the water mains via the new tube supplied
with the appliance (inside the drum). Do not use the old tube for this purpose.
• Connect one end of the water inlet pipe with the elbow bend to the electrovalve
(top rear part of the machine) and the other end to a tap or a plumbed‑in 3/4”
gas threaded connection (�g. 2).
•
Place the appliance close to the wall, ensuring that there are no bends or kinks
anywhere in the tube.
•
Hook the outlet pipe to the edge of the sink or preferably to a xed drainage outlet
of a diameter greater than that of the outlet pipe and at a height of min. 50 cm
and a maximum of 85 cm from the oor (�g. 3).
•
If necessary, use the curved* accessory to attach and support the outlet pipe
more securely.
• Some models may include one or more of the following features:
•
AQUASTOP (�g. 4): a device located on the supply tube that stops water ow
if the tube deteriorates; in this case, a red mark will appear in the window “A”
and the tube must be replaced. To unscrew the nut, press the one‑way lock
device “B”.
•
AQUAPROTECT - SUPPLY TUBE WITH GUARD (�g. 5): should water leak
from the primary internal tube “C”, the transparent containment sheath “D”
will contain water to permit the washing cycle to complete. At the end of the
cycle, contact the Customer Service Centre to replace the supply tube.
1.3 - Aligning the appliance
• Level the machine by adjusting the feet (�g. 6).
a) Turn the nut clockwise to release the screw on the foot.
b) Raise or lower the foot by rotating it until it stands rmly on the oor.
c)
Lock the foot in position by turning the nut anticlockwise until it comes up
against the bottom of the washing machine.
• Check that the appliance is properly levelled.
* Accessory sold separately
max
100 cm
+2.5 m
max
min 50 cm
max 85 cm
Overflow
vent
min
4 cm
QG_Candy_WM_ProWash400_70070922.indb 19QG_Candy_WM_ProWash400_70070922.indb 19 28/03/2025 15:17:4028/03/2025 15:17:40
Bekijk gratis de handleiding van Candy BC448M4D8J-S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Candy |
| Model | BC448M4D8J-S |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 28446 MB |
