BWT BC100+ handleiding
Handleiding
Je bekijkt pagina 3 van 148
- Operating water temperature: 5˚C ( 41˚F ) – 35˚C ( 95˚F ).
- For the purposes of recharging the battery, only use the detachable supply unit ( external adaptor
model number: DSS12D-0841000-B / DSS12D-0841000-C / DSS12D-0841000-D / LX084100U )
- Connect the external adaptor to a power source through a residential current device ( RCD ) / a
ground fault circuit interrupter ( GFCI ). If in doubt, consult a qualified electrician.
- Disconnect the robot from the supply mains and make sure the robot is OFF prior to carrying out
regular maintenance – such as cleaning the filter, swivel smoothing-ring, and the areas around the
- Do not attempt to replace the installed rechargeable Li - ion battery pack.
- You should not operate this robot when people and/or pets are present in the water.
damage the device and other properties.
- Never insert fingers or any object to touch the impeller.
- The built-in battery must be removed by a skilled technician before it is scrapped.
- This robot contains a battery that are only to be removed by skilled persons.
- The robot must be disconnected from the supply mains as the battery is removed.
- For details regarding battery recycling/disposal, refer to the section “BATTERY DISPOSAL” in this
manual and contact your local authorities for more information.
- The battery must be disposed safely in accordance with local ordinances or regulations.
- External adaptor and charging cable:
• Never use the external adaptor and charging cable for anything other than charging the battery of
the robot that is supplied in the same pack.
• The external adaptor and charging cable should not be used outdoors, nor should it be exposed to
rain, humidity, and any liquid or heat.
• The transformer ( or external adaptor ) is to be located outside zone 1.
• Keep the external adaptor and charging cable out of reach of children.
• Never use the external adaptor and charging cable if any damage is detected.
• DO NOT handle the external adaptor and charging cable with wet hands.
• Keep the external adaptor disconnected from power when it is not in use.
• Never attempt to pry open the external adaptor.
• If the supply cord of the external adaptor is damaged, the external adaptor must be replaced by the
manufacturer or its service agent to prevent hazards of any kind.
• Make sure the robot is completely dry before charging.
CAUTION!
- This robot is designed for underwater use only; it is not an all-purpose vacuum cleaner. DO NOT attempt to use it to clean
anything other than your pool.
- Use only the original accessories delivered with this product.
-
DO NOT use this robot right after pool-shocking. It is recommended to first leave the pool circulating for at least 24 - 48 hours.
- If you are planning on using the robot in a saltwater pool, make sure all salt are dissolved before deploying the robot.
- DO NOT use this robot with another automatic cleaner/cleaner simultaneously in the pool.
- Remove hard, sharp objects from the pool before deploying the robot to avoid damages to the robot and its filter.
- To avoid damages to the external adaptor and charging cable, do not attempt to carry the robot by the cord of external
adaptor /charging cable or pull the cord to disconnect it from the power source and charging cable.
- Charge the robot indoors in a clean, dry area with good ventilation and away from sunlight.
- DO NOT leave the robot charged for over 10 hours.
- If the robot will not be used for an extended period, detach it from the charging cable and use a damp cloth to clean and
dry the robot and its accessories. Make sure to charge the robot to about 30% to 50% of the battery capacity before it is
stored. Store it in a well-ventilated area away from sunlight, heat, ignition sources, pool chemicals, and children. Recharge
the robot every three months.
- All actions concerning the disassembly of the swivel head ( ie. battery disposal ) should only be carried out by an authorized
technician.
Above warnings and cautions are not intended to incorporate all possible instances for risks and / or severe injuries.
Pool / spa owners should always exercise extra caution and common sense when utilizing the product.
Remark: Product/parts photos / drawings in this manual are for demonstration only. Product/parts in photos / draw-
ings may vary with the model purchased. Accessories / parts shown in this manual & parts diagram are not necessar-
ily included with every model.
swivel head turns 180˚, allowing the robot to move in the opposite direction. The robot moves in a generally straight pattern in
Fully charge the robot ( about 6 hrs ) before using it for the first time.
Be sure not to invert the charging cable and ensure both the charging cable and
4. When charging is complete, disconnect the external adaptor from the power source and unplug the
Normally the robot can operate up to 45 minutes on a full charge.
Once the lifespan of the battery reaches its end, refer to section “
Let the robot rest for around 30 to 40 minutes before charging it again.
1. Bring the robot to the side of your pool.
First, align and attach the retrieval cord to the side notches at the top as you wrap the cord around the stem (
3. Slide the power switch to “ ” ( while the robot is still submerged ) – the indicator light will turn on and activate the motor
automatically ( water level covering the sensors at the top of the swivel head ). Let the robot sink to the pool floor and observe
retrieve it and redeploy it while making sure its front/back is facing the pool wall
No light - Power off / no power
Light - Power on
Blinking light - Battery power will be exhausted within 5 - 10 minutes.
4. To retrieve the robot from the pool, attach the hook to a telescopic pole ( not provided ) and use it to retrieve the float, if you
( for Australia / New
5. Slide the power switch OFF. Rinse the robot with fresh water after every use. DO NOT use any detergent.
6. Dry the charging port and pins thoroughly (
Before cleaning the debris compartment, make sure the robot is
clips are secured to the base. A “click” sound will
Before redeploying the robot to the pool, hold onto the wings on the body top cover to sway the robot slightly, to ensure
Float Replacement
Use a screwdriver ( not provided ) to unscrew the 4 screws at on the top cover of the swivel head. Untie the knot on the string
Flap replacement
1. Be sure to clean and dry the areas around the charging port and water sensors after every use to avoid the forming of
2. Battery discharges on its own during storage. Make sure to charge the robot to about 30% to 50% of the battery capacity
• Be sure to drain the water from the robot before storage.
temperature for storage should be 10˚C – 25˚C ( 50˚F – 77˚F ).
- Battery does not charge fully.
Battery operation time is noticeably reduced. Observe and record the run times of the first few operations ( on a full charge ).
could cause sparking and/or short circuit the battery.
Follow section “
2. Use the screwdriver to unscrew the 4 screws located at the bottom of the head to release the
3. Remove out the battery pack to expose the PCBA. To detach the battery connection wire, press
2021/10 : AMAINTENANCE & CLEANING
bwt.com
ENGLISH
2/147
Bekijk gratis de handleiding van BWT BC100+, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | BWT |
| Model | BC100+ |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 41474 MB |
