Bushnell R5 handleiding
Handleiding
Je bekijkt pagina 4 van 33
4
Click to return to the Table of Contents.
MOUNTING YOUR RIFLESCOPE
Your new scope, even with its technologically advanced design and features, will not perform at its best if not properly mounted.
One of the most important contributing factors to the precision of your scope and rifle is the selection of the mount and the care
with which mounting is done. Dependable mounts that attach your scope securely to the rifle will reward you with precision and
repeatability. You should take as much care in selecting a mounting system as you did in selecting your scope.
Remember, not all scopes are compatible with all mounts on all rifles. If there is any doubt in your mind, you should seek the advice of
your local retailer or gunsmith.
WARNING: A RIFLESCOPE SHOULD NEVER BE USED AS A SUBSTITUTE FOR EITHER A BINOCULAR OR
SPOTTING SCOPE. IT MAY RESULT IN YOU INADVERTENTLY POINTING THE FIREARM AT ANOTHER PERSON.
PRELIMINARY SCOPE ADJUSTMENTS - SETTING THE DIOPTER
WARNING: DO NOT LOOK TOWARDS THE SUN WHILE SETTING THE DIOPTER!
Before installing the scope, we recommend you set the diopter adjustment to fit your individual eyesight. Refocusing the diopter will
result in a sharper reticle focus, an improved optical image, and will help to avoid eye fatigue when using the scope for prolonged
periods of time. To refocus, hold the scope about 3 to 4 inches from your eye and point at a flatly lit area such as a light colored
painted wall.
Quickly glance into the scope. If the reticle appears blurred at first glance, it is out of focus. Turn the eyepiece clockwise or counter
clockwise while looking into the scope until reticle sharpness is improved. Look away from the eyepiece for a couple of seconds and
then glance into the scope again to check the sharpness of the reticle. Remember to take quick glances, as the eye will compensate
for slightly out of focus conditions with prolonged looks. If the reticle does not appear in focus right away, continue to make fine
adjustments. Repeat this procedure until the reticle is sharp and clearly defined right away when looking into the scope.
Unless your eyes undergo a significant change over the years, you will not have to make this adjustment again.
ACTIVATING THE BATTERY
Before powering on your scope’s illumination feature for the first time, you must activate the installed CR2032 lithium battery by
removing the isolator disc.
1. Unscrew the battery cap counterclockwise, located on the end of the Illumination Control
on the left side of the scope. We suggest holding the Illumination Control Ring steady
while unscrewing the battery cap.
2. Once the cap is off, tip the battery out of the scope. Locate the plastic disc and remove it.
3. Replace the battery and battery cap.
Should your reticle grow dim or not light, replace the battery, following the installation
procedure described above.
CAUTION: Improper installation of the battery may damage the internal contacts. Ensure
that the positive (+) side faces up and the negative (-) side is down.
ATTACHING A MOUNT, RINGS AND SCOPE TO YOUR RIFLE
WARNING: BEFORE BEGINNING THE MOUNTING PROCEDURE, BE SURE THE ACTION IS OPEN, THE CLIP OR
MAGAZINE IS REMOVED AND THE CHAMBER IS CLEAR. DO NOT ATTEMPT ANY WORK UNTIL YOUR FIREARM
HAS BEEN CLEARED AND DETERMINED TO BE SAFE.
WARNING: IF THE SCOPE IS NOT MOUNTED FAR ENOUGH FORWARD, ITS REARWARD MOTION MAY INJURE
THE SHOOTER WHEN THE RIFLE RECOILS.
In mounting your scope, we recommend that you DO NOT take short cuts as it may lead to damage to either the mounting system or
to the scope. Each mounting system will have its own instructions to follow, and it is best to read the instructions first to be sure you
understand them and have the necessary tools on hand.
We further recommend that you plan to go through the mounting procedure twice. The first time, to be sure everything fits together
and functions properly. On the first run through, please keep the following in mind:
› Before attaching the base, clean the mounting holes in the receiver and the threads of the attaching screws with high concentrate
rubbing alcohol or any good solvent to free them of oil or grease.
› If the mount manufacturer has recommended the use of a thread adhesive, do not use it on the first mounting trial. Once adhesive
has set, it is difficult to demount if anything needs correction and will leave residue.
› Be sure the mounting screws do not protrude into the receiver.
› When using dovetail, twist-in or twist-and-lock ring mounts, do not use the scope as a lever when installing the scope. The initial
resistance to turning may cause damage to the scope and is not covered by the warranty. We recommend using a wooden dowel
or metal cylinder to seat the rings.
› Be sure the position of the scope does not interfere with the operation of the action.
Note: Remove the plastic disc under the
button battery before first use.
Bekijk gratis de handleiding van Bushnell R5, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bushnell |
| Model | R5 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7861 MB |
