Handleiding
Je bekijkt pagina 6 van 28
6
¡ Once you have established the connections, carry
out a test for leaks.
WARNING‒Risk of explosion!
Escaping gas may cause an explosion.
▶
All Installation, connection, regulating and conver-
sion work to a different gas type must be carried
out by an authorised professional while taking into
account the respective applicable regulations and
legal requirements as well as the regulations re-
garding the local electricity and gas suppliers.
Special attention must be paid to the provisions
and guidelines that are applicable for the ventila-
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
¡ Ensure that the kitchen is sufficiently ventilated, in
particular when operating the gas cooking appli-
ance.
¡ Do not connect the appliance to an exhaust gas
system for combustion products.
¡ Never install the appliance in boats or in vehicles.
¡ The warranty applies only when using the appli-
ance as intended.
¡ Before installing the appliance, check that the
local conditions of the supplier are compatible
with the appliance settings specified on the rating
plate (type of gas and pressure, power, voltage).
¡ Secure the power cord to the cabinet to prevent it
from touching hot parts of the oven or hob.
¡ Before any work is carried out on the appliance,
switch off the power supply and the gas supply.
¡ Connect the appliance to the power supply using
the earth.
¡ Do not make any changes to the inside of the ap-
pliance. If required, contact our technical cus-
tomer service.
Before installing
¡ This appliance is a class 3 appliance in accordance
with the EN 30-1-1 standard for gas appliances:
Built-in appliance.
¡ This appliance can be combined with other hobs of
the same brand by using the connection accessory.
See catalogue.
¡ The unit in which the appliance is installed must be
stable and secured appropriately.
¡ The units in the vicinity of the appliance, the lamin-
ated panels and the adhesive with which they are
secured must be made of non-flammable, heat-res-
istant materials.
¡ Do not install this appliance above refrigerators,
washing machines, dishwashers or similar.
¡ The appliance must only be installed on an oven
with forced ventilation. Check the dimensions of the
oven in the installation instructions for the oven.
¡ If you install an oven underneath the hob, the work
surface thickness may differ from the dimensions
given in these instructions. Take note of the informa-
tion in the oven installation instructions.
¡ If you install an exhaust air fan or an extractor hood,
refer to the installation instructions for these. Always
observe the minimum vertical distance to the hob.
→Fig.
1
Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions.
¡ In recesses of 500 mm, the appliance must be in-
stalled on the front edge of the recess. →"Position-
ing the appliance", Page6
→Fig.
2
¡ Any panel that is attached closer to the built-in niche
than the specified clearance must be made of non-
combustible material. Always maintain a distance of
at least 5mm between the panel and the appliance.
Maximum clearances for the panel: 30 mm thick-
ness x 70 mm height.
¡ Seal the cut surfaces of wooden work surfaces with
a special glue seal to protect them from moisture.
Preparing the built-in unit for standard installation
(a)
¡ Use worktops that are between 20 mm and 50
mm thick.
Note:Worktops that are between 12 mm and 20
mm thick must be used with a spacer, which is avail-
able from technical customer service.
Installation on a drawer or cupboard
WARNING‒Risk of burns!
The accessible parts may become hot during opera-
tion.
If there is no built-in oven underneath the hob and
the underside of the hob is accessible, follow these
instructions:
For gas hobs with wok burner, insert a non-flamable
intermediate floor (e.g. metal or ply-Wood) at a dis-
tance of 10 mm from the hob .
→Fig.
3
For gas hobs without a wok burner, it is advisable to
fit an intermediate floor underneath the hob .
→Fig.
4
In both cases, the distance from the intermediate
floor to the mains connection for the appliance must
be at least 10 mm.
The thickness of the separator must allow for re-
specting the distances in the figure.
Installation above an oven
→Fig.
5
Positioning the appliance
1. Position the hob with the upper side facing down
on a flat, stable surface.
2. Loosen the screws on the brackets so they can
turn freely. You do not need to fully undo the
screws on the brackets.
→Fig.
6
3. Turn the hob around and insert it into the recess.
Insert the hob in the front of the recess.
→Fig.
7
4. Turn the brackets and tighten them fully.
→Fig.
8
The position of the brackets depends on the work-
top thickness.
Note:Do not use silicone to bond the appliance to
the worktop.
Removing the appliance
1. Disconnect the appliance from the electricity and
gas connections.
2. Unscrew the brackets and proceed in reverse or-
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION‒Risk of explosion!
A gas leakage may cause an explosion.
▶
If any connection is handled, check the seal.
¡ Arrange the gas connection so that the shut-off
valve is accessible.
Bekijk gratis de handleiding van Bosch PRB3A6I40, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | PRB3A6I40 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 4349 MB |
