Handleiding
Je bekijkt pagina 9 van 20
Installation instructions en
– a: Pressure test point.
Connecting the unit to the gas line
The supply connection point shall be accessible with the
appliance installed.
Tip: Make sure that all connections performed are free
of leakage. Use pipe compound or thread sealant, prop-
erly threaded pipes and careful assembly procedure so
that there is no cross threading and so on, which might
cause damage or leakage.
The manufacturer does not accept any liability for leak-
age on connections performed by the installer or if the
L-tube is moved or twisted.
Refer to AS/NZS 5601.1 for piping size details.
Remove plastic cap from gas supply line prior to in-
stallation.
There are two ways to carry out the connection to the
main gas line:
– Connect with rigid pipe as specified in AS/NZS
5601.1.
– Connect with flexible hose. The hose assembly
must comply with AS/NZS 1869, 10mm ID, class
B or D, no more than 1.2m long and installed in
accordance with AS/NZS 5601.1.
Note
If installing with a hose assembly:
Ensure that the hose assembly is restrained from ac-
cidental contact with the flue outlet of an underbench
oven.
Ensure that the hose does not contact the hot sur-
faces of the hotplate, oven, dishwasher or any other
appliance that may be installed underneath or next to
the hotplate.
The hose should not be subjected to abrasion, kink-
ing or permanent deformation.
The hose should be able to be inspected along its
entire length with the cooktop in the installed position.
Unions compatible with the hose fittings must be
used and all connections tested for gas leaks.
Before leaving
It should be expressly noted that we cannot accept any
liability for direct or indirect damage caused by wrong
connection, leakage or improper installation.
Check all connections for gas leaks with soap and
water. DO NOT use a naked flame for detecting
leaks.
Ignite all burners both individually and concurrently to
ensure correct operation of gas valves, burners and
ignition.
Turn gas taps to low flame position and observe sta-
bility of the flame for each burner individually and all
together.
Adhere the duplicate data plate to an accessible loca-
tion near the hotplate.
When satisfied with the hotplate, instruct the user on
the correct method of operation.
In case the appliance fails to operate correctly after
all checks have been carried out, refer to the author-
ised service provider in your area.
When being repaired, the appliance must always be dis-
connected from the mains supply; if required, notify our
customer service.
2.8 Converting the cooktop from Natural Gas
to ULPG
All work involved in installation, setting and adaptation
to a different gas type must be carried out by a licensed
gas fitter and must comply with current regulations and
the conditions laid down by the local gas company.
Before conversion the cooktop must be disconnected
from the electricity and gas valves must be turned to the
OFF position.
Adjusting the taps
1.
Turn the rotary knobs to the minimum power position
and pull them out.
2.
With the tip of the screwdriver, push down on the flex-
ible rubber holder to access the bypass screw.
If you cannot access the bypass screw, remove the
upper side of the appliance.
"Removing the outer glass plate", Page10
Never remove the sealing ring. The sealing rings pre-
vent liquids and dirt from finding their way into the ap-
pliance and impairing its ability to function properly.
3.
Adjust the bypass screws:
For ULPG: the screw must be fully tightened down
clockwise.
For Natural Gas: replace the control knob onto the
spindle, light the gas and turn the control knob to
the small flame position. Screw the adjustment
screw anti-clockwise to establish a minimum stable
flame position. The flame should remain alight and
not burn back to the injector when the valve is
turned quickly from ‘Full On’ to the “Minimum
flame” position and back a few times.
9
Bekijk gratis de handleiding van Bosch PNK6B6K40A, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | PNK6B6K40A |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 1883 MB |
