Biltema 45-6055 handleiding
Handleiding
Je bekijkt pagina 5 van 26
5
© 2024-11-12 Biltema Nordic Services AB
Art. 45-6055
SE
LÅNGTIDS- OCH VINTERFÖRVARING
Använd inte sandlterpumpen om poolen är frusen,
det kan kan skada pumpen. Om produkten måste
användas med frostskyddsmedel kan även propylen-
glykol användas. Propylenglykol är ett frostskydds-
medel som är skonsamt mot plast. Andra typer av
frostskyddsmedel är inte att rekommendera eftersom
de kan skada produktens plastdetaljer.
Tömning av vattnet
Innan du tömmer vattnet eller återställer poolen, se till
att vattnets utloppsriktning är mot ett dike och bort
från hus och byggnader. Följ lokala bestämmelser för
särskilda krav på vattenrening.
• Stäng av pumpen och dra ur stickkontakten.
• Skruva loss avtappningsventilen (15) moturs för
att helt tömma vattnet i pumpen. Avtappnings-
pluggen sitter i botten av pumpen.
SFP6-
23
-GB(V1)
www.JLeisure-Global.com
12
SFP6-
23
-GB(V1)
www.JLeisure-Global.com
13
pump, check the pressure reading of the
manometer.
Generally, when the pressure of the
0.2bar (3psi) (green area) , it runs normally.
Note: You must make sure that maintenance
begins only after the sand filter pump is
unplugged. Otherwise serious risks such as
personal injury and even death may occur.
Note: Record the reading of the manometer
When the manometer shows a pressure
of 0.2bar (3psi) or higher, please clean up
the sand bend or replace the sand. Use
"backwash" and "rinse" functions.
Note: regular rinsing according to use
situation is recommended.
Long-term storage and storage in winter
Using the product in a frozen pool may damage the product and invalidate the
quality warranty. If the product has to be used with antifreeze, propylene glycol
may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic
parts. Other types of antifreeze are highly toxic and may be harmful to the product’s
plastic elements.
1.Before discharging the water or repostioning of the pool, make sure the discharge
direction is towards the discharging ditch and away from the home. Review local
regulations for special water treatment requirements.
3.After emptying, remove all connected sand filter pumps, corrugated tubes and
4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty
water inside the body. The drain plug is at the bottom of the body.
6.Lubricate the seal rings and washers in the order below for long-term storage.
7.The best practice for product storage is to dry the parts and motor and replace
them in the original package. To avoid shrinkage or corrosion, do not cover or wrap
the motor with a plastic bag.
8.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).
Location of
control valve
Functions
Filter
and then enters the pool
Backwash
and is then directly discharged
from the drain outlet.
Rinse
startup. Sand in the sand tank
is rinsed and the sand bed after
backwashing is leveled.
and is then directly discharged
from the drain outlet.
Drain
Discharged directly from the drain
outlet, used to lower water level
or discharge water from the pool
Discharged directly from the
pump without passing through
Recirculation
Circulates pool water without
through the control valve of the
Closed /
• Efter tömning, koppla loss sandlterpumpen,
slangarna och lterkåpan.
• Låt pumpen och alla delar och slangar torka.
• Smörj tätningsringar och brickor före långtidsför-
varing.
• Förvara gärna pumpen och dess delar i original-
förpackningen
• För att undvika krympning eller korrosion, lägg
inte motorn i en plastpåse.
• Förvara pumpen med motor och alla delar på en
torr plats vid 0–40 °C.
MANOMETER
SFP6-
23
-GB(V1)
www.JLeisure-Global.com
12
SFP6-
23
-GB(V1)
www.JLeisure-Global.com
13
pump, check the pressure reading of the
manometer.
Generally, w hen the pre s sur e of the
0.2bar (3psi) (green area) , it runs normally.
Note: You must make sure that maintenance
begins only after the sand filter pump is
unplugged. Otherwise serious risks such as
personal injury and even death may occur.
Note: Record the reading of the manometer
When the manometer shows a pressure
of 0.2bar (3psi) or higher, please clean up
the sand bend or replace the sand. Use
"backwash" and "rinse" functions.
Note: regular rinsing according to use
situation is recommended.
Long-term storage and storage in winter
Using the product in a frozen pool may damage the product and invalidate the
quality warranty. If the product has to be used with antifreeze, propylene glycol
may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic
parts. Other types of antifreeze are highly toxic and may be harmful to the product’s
plastic elements.
1.Before discharging the water or repostioning of the pool, make sure the discharge
direction is towards the discharging ditch and away from the home. Review local
regulations for special water treatment requirements.
3.After emptying, remove all connected sand filter pumps, corrugated tubes and
4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty
water inside the body. The drain plug is at the bottom of the body.
6.Lubricate the seal rings and washers in the order below for long-term storage.
7.The best practice for product storage is to dry the parts and motor and replace
them in the original package. To avoid shrinkage or corrosion, do not cover or wrap
the motor with a plastic bag.
8.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).
Location of
control valve
Functions
Filter
and then enters the pool
Backwash
and is then directly discharged
from the drain outlet.
Rinse
startup. Sand in the sand tank
is rinsed and the sand bed after
backwashing is leveled.
and is then directly discharged
from the drain outlet.
Drain
Discharged directly from the drain
outlet, used to lower water level
or discharge water from the pool
Discharged directly from the
pump without passing through
Recirculation
Circulates pool water without
through the control valve of the
Closed /
OBS! Kontrollera trycket under drift. Det ska ligga
inom det görna fältet och inte överstiga 0,2 bar. När
trycket ligger inom det gröna området, 0,2 bar (3 psi),
fungerar sandlterpumpen normalt.
VARNING! Före underhåll måste pumpen stängas av
och kopplas ifrån strömuttaget. Annars nns det risk
för allvarliga personskador och till och med dödsfall.
OBS! Kontrollera trycket regelbundet. Om trycket
ligger högre än 0,2 bar (3 psi) under drift, måste
sanden rengöras eller bytas ut. Använd funktionerna
"backspolning" och "sköljning".
OBS! Skölj pumpen regelbundet beroende på hur
mycket poolen används.
Bekijk gratis de handleiding van Biltema 45-6055, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Biltema |
| Model | 45-6055 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3973 MB |
