Beurer HK 43 handleiding
Handleiding
Je bekijkt pagina 12 van 66
12
6. OPERATION
6.1 Safety
NOTICE
•
The device is fitted with a SAFETY SYSTEM. This sensor
technology provides protection against overheating across the
entire surface of the heating element with an automatic switch-
o in the event of afault. If the SAFETY SYSTEM has switched
o the device, the control will no longer light up in any way, even
when switched on.
•
Please note that for safety reasons, the device can no longer be
operated after a fault has occurred and must either be disposed
of or be sent to the specified service address.
•
Do not under any circumstances connect the defective heating
element with another control of the same type. This would
also trigger apermanent switch-o by the safety system in the
control.
6.2 Initial use
NOTICE
Ensure that the heating element will not bunch up or become folded
during use.
1.
First, connect the control
2
to
the heating element by inserting
the plug-in coupling
6
.
2.
Then plug the mains plug
1
into
the socket.
6.3 Switching on
Press the ON-OFF button
3
. When switched on, the temperature
settings display
5
is lit up.
Switching sequence: 3-1-2-3-1...
6.4 Setting the temperature
To change the temperature, press the button for setting the
temperature
4
.
Setting 1: Minimum heat
Setting 2: Medium heat
Setting 3: Maximum heat
The fastest way to warm up the device is to initially set the
highest temperature setting.
This device has afast heating function, which allows the
device to warm up quickly in the first 10 minutes.
6.5 Automatic switch-o
This device is equipped with an automatic switch-o function.
This turns o the heat supply and the temperature settings display
approx. 90 minutes after the initial use of the device. Press the
ON-OFF button
3
to be able to restart the device. After about
5seconds it is possible to switch it on again.
WARNING
If the device is being used over several hours, we recommend
that you set the lowest temperature setting on the control to avoid
overheating the body part being heated, which may lead to burns
to the skin.
6.6 Switching o
Press the ON-OFF button
3
to switch off the device. The
temperature settings display is no longer illuminated.
If the device is not in use, press the ON/OFF button
3
to switch o the device and pull the power plug out of
the socket.
Then disconnect the control
2
from the heating element
by unplugging the plug-in coupling
6
.
7. CLEANING AND MAINTENANCE
WARNING
Before cleaning, always remove the power plug from the socket first.
Then disconnect the control from the heating element by unplugging
the plug-in coupling. Otherwise there is arisk of electric shock.
NOTICE
The control must never come into contact with water or other liquids,
as this may cause damage.
•
To clean the control, use adry, lint-free cloth. Do not use any
chemical or abrasive cleaning agents.
•
Small marks on the heating element can be removed with
adamp cloth and, if necessary, with alittle liquid detergent for
delicate laundry.
NOTICE
Please note that the heating element must not be chemically
cleaned, wrung out, tumble dried, put through amangle or ironed.
Otherwise the heating element may get damaged.
•
The heating element is machine-washable.
•
Set the washing machine to aparticularly gentle wash cycle at
30°C(wool cycle). Use adelicate laundry detergent and measure
it out according to the manufacturer’sinstructions.
•
Immediately after washing, reshape the heating element to its
original dimensions while it is still damp and spread it out flat
on aclothes horse to dry.
NOTICE
•
Do not use pegs or similar items to attach the heating element
to the clothes horse. Otherwise the heating element may get
damaged.
•
Do not reconnect the control to the heating element until the
plug-in coupling and heating element are completely dry.
Otherwise the device may get damaged.
WARNING
Never switch the device on to dry it! Otherwise there is arisk of
electric shock.
8. WHAT IF THERE ARE PROBLEMS?
Problem
The temperature settings are not illuminated
despite the fact that
- the control is properly connected to
the heating element
- the power plug is connected to awork
-
ing socket
- the ON/OFF button
3
has been
pressed.
Possible cause The safety system has switched the device
o permanently.
Solution Send the heating element and the control for
servicing.
Bekijk gratis de handleiding van Beurer HK 43, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Beurer |
| Model | HK 43 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7489 MB |
