Bertazzoni PRO96L2EROT handleiding
Handleiding
Je bekijkt pagina 9 van 40
9
WARNING: A
fter completing the above-mentioned replacements, adjust the
burners, as described in the paragraph below. Seal any adjustment and pre-
adjustment devices. Replace the existing rating plate with a new one corresponding
to the new gas adjustment. This rating plate is contained in the spare nozzle
bag.
Adaption to various types of gas APPLIANCE CATEGORY:
II
2H3+
Burner Types of Gas Pressure Nozzle
Diameter
Rater Capacity Reduced
Capacity
by-pass
Diameter
mbar 1/100 mm.
g
/h l/h kw kcal/h kw kcal/h 1/100 mm.
Natural G20 20 77 - 95 1 860 0,48 413 34 reg.
Auxiliar
y
Butane G30 30 50 73 - 1 860 0,48 413 34
Propane G31 37 50 71 - 1 860 0,48 413 34
Natural G20 20 101 - 167 1,75 1505 0,6 516 36 re
g
.
Semi-Rapid Butane G30 30 66 127 - 1,75 1505 0,6 516 36
Propane G31 37 66 125 - 1,75 1505 0,6 516 36
Natural G20 20 129 - 286 3 2580 1,05 903 52 reg.
Rapid Butane G30 30 87 218 - 3 2580 1,05 903 52
Propane G31 37 87 214 - 3 2580 1,05 903 52
Na
tural G20 20
Int 70
-
476
5,0 4300 0,48 413
Int 34 re
g
.
Ext 2 x 110 Ext 65 re
g
Dual
Butane G30 30
Int 46
334
-
4,6 3956 0,48 413
Int 34
Ext 2 x 69 Ext 65
Pr
opane G31 37
Int 46
328
-
4,6 3956 0,48 413
Int 34
Ext 2 x 69 Ext 65
Natural G20 20 150 - 429 4,5 3870 2 1720 70 re
g
.
Oven Butane G30 30 95 327 - 4,5 3870 2 1720 70
90X60 Propane G31 37 95 321 - 4,5 3870 2 1720 70
Natural G20 20 125 - 286 3 2580 1 860 48
Oven Butane G30 30 85 218 - 3 2580 1 860 48
60X60 Propane G31 37 85 214 - 3 2580 1 860 48
Check correct operation of the ignition system and operation of burners individually
and in combination. Burner flames should be clear blue, with no yellow tipping. If the
burners show any abnormality check that burner heads are correctly located.
Note: These burners have no aeration adjustment.
Burner "MINIMUM" adjustment:
Wo
rk surface burner adjustment: follow the instructions below to adjust the work
surface burner minimum:
- Light the burner and set the knob to the MINIMUM position (small flame)
.
-
Remove the knob of the valve that is press-fit on the rod of that valve.
-
Insert a small slotted screwdriver into the hole on the valve body (Fig.10A) an
d
tur
n the choke screw to the right or left until the burner flame is adjusted
to
min
imum.
- For the gas valve of dual burner the choke valve is located on the valve body
(fig. 10B) , the A screw adjust the outer ring, the B screw adjust the inner ri
ng.
-
Make sure that the flame does not go out when switching quickly from the
MAX
IMUM to the MINIMUM position.
Fig 10A Fig 10B
WARNING: The above-mentioned adjustment should be made only with natural gas
burners, while those operating with liquid gas the screw must be locked at the end
in a clockwise direction.
Test the operation of It should be noted that Bertazzoni SpA cannot accept any liability for direct or
the cooker before indirect damage caused by incorrect connection or improper installation. When
leaving being repaired, the appliance must always be disconnected from the mains supply; if
required, notify our customer service.
Bekijk gratis de handleiding van Bertazzoni PRO96L2EROT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bertazzoni |
| Model | PRO96L2EROT |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 4815 MB |
