Handleiding
Je bekijkt pagina 6 van 26
R59xxxx /00 IBX
IBX SERIES
6
single fault condition testing ensures the safety of the equipment to the user even when the equipment's normal
operation fails.
Product care
Structural & mounting components should be kept dry, clean, lubricated (only if recommended), coated properly,
and otherwise maintained in a manner consistent with part design. Barco products must be used in a manner
consistent with their design and inspected on a routine basis for security, wear, deformation, corrosion and any
other circumstances that may affect the load handling capability of the part.
Barco recommends inspections at regular intervals for all installations and increasing in frequency for more
critical installations. If a part is found to have damage, which may cause a decrease in load capability, the part
must be removed for service or replaced immediately.
Under no circumstances are Barco parts repairable by anyone other than Barco.
1.2 Important safety instructions
Instructions:
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the
manufacturer for further advice should any doubts exist regarding any cleaning procedure.
• Do not block ventilation openings. Install in accordance with the manufacturers instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs
are damaged then replacement of the defective parts must be undertaken immediately.
• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus. Replace damaged power/data cords immediately.
• Only use attachments/accessories specified by the manufacturer.
• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning
protection. Unplug this apparatus when unused for long period of time.
• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, the apparatus does not operate normally,
or has been dropped.
• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use caution
during lifting/moving or transporting to avoid damage by possible tipping.
• Do not use damaged LED tiles. Replace damaged parts immediately.
1.3 Important warnings
Important warnings:
Risk of electric shock:
Do not open. To reduce the risk of electric shock, do not remove LED board from tile. No user-serviceable parts
inside. Refer servicing to qualified service personnel.
Maximum and minimum ambient temperature:
The maximum ambient temperature for the LED wall is 40°C (104°F), the minimum temperature is -20°C (-4°F).
Low Voltage Surge Protection Device required
Due to the damaging effects of lightning, utility switching and switching electric motors of other users on the
mains, this product needs to be protected by means of a Surge Protection Device. This product is connected to
the mains through a power distribution box from another party, please verify that a Low Voltage Surge Protection
Device according IEC/EN61643-11 or UL 1449 is in place.
High leakage current:
The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid
risk of electric shock due to high leakage current, proper grounding of the installation is required.
Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred into heat.
The installation should be such that the amount of air flow required for safe operation of the equipment is not
compromised. Proper ventilation must be provided.
Risk of electric shock / Risk of fire:
Use single-phase power supply for an LED display with the total power consumption not exceeding 3 kW, and
three-phase power supply for an LED display with the total power consumption exceeding 3 kW.
Each power source cable should be protected by a circuit breaker or fuses rated 16 A / 250 VAC (15 A / 250 VAC
in the USA and Canada). Note that one tile requires 100-240 VAC, 50-60 Hz.
To protect against risk of fire caused by overloading of power cables, the number of tiles connected in parallel is
limited, see table below.
Bekijk gratis de handleiding van Barco IBX1.2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Barco |
| Model | IBX1.2 |
| Categorie | Monitor |
| Taal | Nederlands |
| Grootte | 10519 MB |
