Axxess AXDIS-MZ1 handleiding
Handleiding
Je bekijkt pagina 5 van 8
5
REV. 11/22/24 INSTAXDIS-MZ1
For the steps below, the LED located inside the interface can only be seen while active. The
interface does not need to be opened to see the LED.
1. Start the vehicle.
2. Connect the AXDIS-MZ1 harness to the wiring harness in the vehicle.
3. The LED will initially turn on solid Green, then turn off for a few seconds while it auto
detects the radio installed.
4. The LED will then flash Red up to (24) times indicating which radio is connected to the
interface, and then turn off for a couple of seconds. Pay close attention to how many Red
flashes there are. This will help in troubleshooting, if need be. Refer to the LED feedback
section for more information.
5. After a couple seconds the LED will turn on solid Red while the interface auto detects the
vehicle. This process should take 5 to 30 seconds.
6. Once the vehicle has been auto detected by the interface, the LED will turn on solid Green
indicating programming was successful.
7. Test all functions of the installation for proper operation, before reassembling the dash.
8. If the interface fails to function, refer to Resetting the AXDIS-MZ1.
Note:
The LED will turn on solid Green for a moment, and then turn off under normal
operation after the key has been cycled.
PROGRAMMING THE AXDIS-MZ1
LED Feedback: The (24) Red LED flashes represent what brand radio the AXDIS-MZ1 believes
it is connected to. Each flash represents a different radio manufacturer. For example, if you
are installing a JVC radio, the AXDIS-MZ1 will flash (5) times. Following is a legend that dictates
which manufacturer corresponds to which flash.
STEERING WHEEL CONTROL SETTINGS
Continued on the next page
LED Feedback Legend
Flash Count
Radio
1 Eclipse (type 1)
2 Kenwood
3 Clarion (type 1)
4 Sony/Dual
5 JVC
6 Pioneer/Jensen
7 Alpine
8 Visteon
Flash Count
Radio
9 Valor
10 Clarion (type 2)
11 Metra OE
12 Eclipse (type 2)
13 LG
14 Parrot
15 XITE
16 Philips
Flash Count
Radio
17 TBD
18 JBL
19 Insane
20 Magnadyne
21 Boss
22 Axxera
23 Axxerra (type 2)
24 Alpine (type 2)
KEYNOTES
*Note: If the AXDIS-MZ1 flashes Red (7) times, and you do not have an Alpine radio connected to it, that
means the AXDIS-MZ1 does not detect a radio connected it. Verify that the 3.5mm jack is connected to the
correct steering wheel jack/wire in the radio.
**Note: The AXSWCH-PAR is required (sold separately). Also, the Parrot radio must be updated to rev.
2.1.4 or higher through www.parrot.com.
†Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to
the other Clarion radio type; same for Eclipse. The following section explains how to do this.
‡Note: If you have a Kenwood radio and the LED feedback comes back as showing as a JVC radio, change
the radio type to a Kenwood. The following section on Changing Radio Type explains how to do this.
Bekijk gratis de handleiding van Axxess AXDIS-MZ1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Axxess |
| Model | AXDIS-MZ1 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 895 MB |
