Axxess AXDIS-GM13 handleiding
Handleiding
Je bekijkt pagina 5 van 16
5
REV. 11/1/24 INSTAXDIS-GM13
LED Feedback Legend
Changing Radio Type
If the LED flashes do not match the radio you have connected, you must manually program the
AXDIS-GM13 to tell it what radio it is connected to.
1. After (3) seconds of turning the key on, press and hold the Volume-Down button on the
steering wheel until the LED in the AXDIS-GM13 goes solid.
2. Release the Volume-Down button; the LED will go out indicating we are now in Changing
Radio Type mode.
3. Refer to the Radio Legend to know which radio number you would like to have
programmed.
4. Press and hold the Volume-Up button until the LED goes solid, and then release. Repeat this
step for the desired radio number you have selected.
5. Once the desired radio number has been selected, press and hold the Volume-Down button
on the steering wheel until the LED goes solid. The LED will remain on for about (3) seconds
while it stores the new radio information.
6. Once the LED goes off, the Changing Radio Type mode will then end. You can now test the
steering control wheel controls.
Note:
If at any time the user fails to press any button for a period longer than (10) seconds, this
process will abort.
Attention:
The Axxess Updater App can also be used to program the following (3) sub-sections
as well, pending that the interface has been initialized and programmed.
Continued on the next page
The (24) Red LED flashes
represent a different
radio manufacturer for
the AXDIS-GM13 to detect.
For example, if you are
installing a JVC radio, the
AXDIS-GM13 will flash Red
(5) times, then stop.
STEERING WHEEL CONTROL SETTINGS
Flash Count
Radio
1
Eclipse (type 1) †
2
Kenwood ‡
3
Clarion (type 1) †
4
Sony / Dual
5
JVC
6
Pioneer / Jensen
7
Alpine *
8
Visteon
9
Valor
10
Clarion (type 2) †
11
Metra OE
12
Eclipse (type 2) †
Flash Count
Radio
13
LG
14
Parrot **
15
XITE
16
Philips
17
TBA
18
JBL
19
Insane
20
Magnadyne
21
Boss
22
Axxera
23
Axxerra (type 2)
24
Alpine (type 2)
KEYNOTES
* If the AXDIS-GM13 flashes RED (7) times, and an Alpine radio is not installed, that means there is an
open connection not accounted for. Verify that the 3.5mm jack is connected to the correct steering wheel
jack/wire in the radio.
** The AXSWCH-PAR is required (sold separately). Also, the software in the radio must be rev. 2.1.4 or higher.
† If a Clarion or Eclipse radio is installed and the steering wheel controls do not function, change the
radio to Clarion (type 2) or Eclipse (type 2) respectively. If the steering wheel controls still do not
function, refer to the Changing Radio Type document available at axxessinterfaces.com.
‡ If a Kenwood radio is installed and the LED feedback flashes (5) times instead of (2), manually change
the radio type to Kenwood. To do this, refer to the Changing Radio Type document on next page, also
available at axxessinterfaces.com.
Bekijk gratis de handleiding van Axxess AXDIS-GM13, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Axxess |
| Model | AXDIS-GM13 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1733 MB |
