Atlona AT-UHD-HDVS-300-KIT handleiding
Handleiding
Je bekijkt pagina 12 van 50
AT-UHD-HDVS-300-KIT
12
1. Connect up to two UHD/HD sources to the HDMI IN 1 and HDMI IN 2 ports.
2. Connect a VGA source to the VGA IN port.
3. Connect up to two USB host devices to the USB 1 and USB 2 ports, using USB A/B cables. Both USB 1.1 and
USB 2.0 are supported.
4. OPTIONAL: Connect a 3.5 mm mini-stereo cable from the AUDIO port to an analog audio source. Making this
connection will allow audio to accompany the source connected to VGA IN.
5. OPTIONAL: Connect the included 3-pin captive screw connector block from the RS-232 port to an automation
control device. This port provides pass-through control of the RS-232 device connected to the AT-UHD-HDVS-
300-RX.
6. Connect up to two USB devices (e.g. keyboard, mouse device, etc.) to the USB HUB ports. Both USB 1.1 and
USB 2.0 are supported. Maximum current draw for this hub is 1.5 A. Maximum current draw for both transmitter
and receiver is 2.5 A.
7. Connect an Ethernet cable from the HDBaseT OUT port to the HDBaseT IN port on the AT-UHD-HDVS-300-RX.
Ethernet cables should use EIA/TIA-568B termination.
8. Connect an Ethernet cable, up to 330 feet (100 meters), from the LAN port to the Local Area Network (LAN).
An automation control system can also be connected to the network, allowing pass-through IP control to an
IP-controlled device connected to the AT-UHD-HDVS-300-RX. Connecting this port to the LAN will also provide
access to the built-in web GUI. Refer to The Web GUI (page 29) for more information. Ethernet cables should
use EIA/TIA-568B termination.
1. Connect an HDMI cable from the HDMI OUT port to a UHD/HD display.
2. Connect an HDMI cable from the HDMI IN 5 port to a UHD/HD source.
3. OPTIONAL: Connect the included 3-pin captive screw connector block from the RS-232 port to an RS-232
device. This port provides both pass-through control from the automation control system, connected to the AT-
UHD-HDVS-300-TX, or display control to the device connected to the AT-UHD-HDVS-300-RX.
4. Connect up to three USB devices (e.g. keyboard, mouse device, etc.) to the USB HUB ports. Both USB 1.1 and
USB 2.0 are supported. Maximum current draw for this hub is 1.5 A. Maximum current draw for both transmitter
and receiver is 2.5 A.
5. Connect an Ethernet cable from the HDBaseT IN port to the HDBaseT OUT port on the AT-UHD-HDVS-300-TX.
Ethernet cables should use EIA/TIA-568B termination.
6. Connect an Ethernet cable, up to 330 feet (100 meters), from the LAN port to the Local Area Network (LAN).
An automation control system can also be connected to the network, allowing pass-through IP control to an
IP-controlled device connected to the AT-UHD-HDVS-300-RX. Connecting this port to the LAN will also provide
access to the built-in web GUI. Refer to The Web GUI (page 29) for more information. Ethernet cables should
use EIA/TIA-568B termination.
7. Connect the included power supply to this port using the included 2-pin captive screw connector. Refer to
Power (page 11) for wiring information.
Connection Instructions
Installation
Transmitter
Receiver
Bekijk gratis de handleiding van Atlona AT-UHD-HDVS-300-KIT, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Atlona |
| Model | AT-UHD-HDVS-300-KIT |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6185 MB |
