Aspes ATE50S handleiding

Handleiding

12345678910111213141516/ 16

Afdrukken

Je bekijkt pagina 6 van 16

6 Instructions for use and maintenance

EN

Attention! Other type of stopping armature is not

allowed between the protection return valve (the

protective device) and the appliance.

Attention! The attaching of the safety return-valve

to threads longer than 10 mm is not allowed,

otherwise this may damage the valve and poses

danger for your appliance.

Attention! With appliances for vertical assembly,

the safety valve has to be connected to the ingoing

pipe with the safety plastic panel of the appliance

being taken o. After it has been assembled it should be in

position as shown on Fig. 3 and g.4.

Attention! The safety valve and the pipe between the

valve and the water heater must be protected from

freezing. During hose draining - its free end must be

always open to the atmosphere (not to be immersed). Make

sure that the hose is also protected from freezing.

Opening the cold-water stopcock of the water supply

piping network and opening the hot-water stopcock

of the water-mixing faucet carries out the lling of the

water heater with water. After the lling is complete,

a constant stream of water must begin to ow from

the water-mixing faucet. Now you can close the hot

water stopcock.

In the event you must empty the water heater, rst

you must cut o󰀨 its power supply. The inow of

water from the water mains must rst be terminated

and the hot water tap of the mixing-faucet must be

opened. The water tap 7 (g 4) must be opened to

drain the water from water tank. If there is no such

tap build in the pipe line, than the water can be drain

directly from inlet pipe of water tank .In the event of

removing the ange, the discharge of several liters

of water, which remain in the water tank, is normal.

Attention! Measures must be undertaken to

prevent damage from discharging water during

draining. In the event that the water mains piping,

pressure exceeds the pressure stated on the appliance

(outlined here above in s. II and on the appliance’s rating

plate), it shall be necessary to mount a pressure-reducing

valve; otherwise the water heater shall not function

correctly. The Manufacturer does not assume any liability

for problems arising out of the appliance’s improper use.

3. Water heater connection to the electrical

network (Fig.2)

Explanations to Fig. 2:

TS - thermal switch; TR - thermal regulator; R -

heater; IL - light indicator; F - ange.

Attention! Make sure the appliance is full of water

prior to switching on the electrical mains power.

3.1. Models with power cord with a plug are

connected by inserting the plug into a contact. They

are switched o󰀨 the power supply by drawing the

plug out of the contact.

Attention! The wall-plug must be properly

connected to a separate electrical circle that is

provided with a protector. It must be earthed.

3.2. Models without power cord

The appliance has to be connected to a separate

electricity circuit of the stationary electrical wiring.

The circuit has to be supplied with a safety fuse

16A (20A for power > 3700W). Copper single core

(rigid – non stranded) conductor shall be used for

the connection – cable 3 x 2.5 mm² (cable 3 x 2.5

mm² for power > 3700W).

The electrical circuit supplying the appliance must

have an in-built device ensuring the splitting of all

terminal poles under conditions of super-voltage of

category III.

To install the power supply wire to the appliance,

remove the plastic cover (Fig.3).

Connect the power wires in compliance with the

marks on the terminals, as follows:

•

the phase - to mark A, A1, L or L1;

•

the neutral - to N (B or B1 or N1)

The safety wire must be obligatory connected to the

screw joint marked with .

After the installation, put the plastic cover back in

its place!

Note: For models with externally adjustable

thermostat (shown on Fig. 3), dismount the

handle before mounting the cover by pressing it

from the internal side till it gets detached from the

plastic cover. Mount the plastic cover again,

afterwards set the handle on its place by pressing it

to click in.

VI. RUST PROTECTION MAGNESIUM

ANODE

The magnesium anode protects the water tank’s

inner surface from corrosion.

The anode element is an element undergoing wear

and tear and is subject to periodic replacement.

Caution: The anode protector MUST be checked,

and changed if needed, after each year of

exploatation.

For replacements, please contact the authorized

service stations!

VII. OPERATION

Switch on:

Before switching on the appliance for rst time, make

sure that the water heater is properly connected to

the power supply network and full with water.

The appliance is switched on by a switch integrated

into the installation, described in item 3.2 of Section

V, or upon connecting the plug to the electrical

contact (in the case of an extension cable with plug).

IMPORTANT: Models that do not have thermostat

control knobs have automatic water temperature

preset by the manufacturer.

12345678910111213141516/ 16

Bekijk gratis de handleiding van Aspes ATE50S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Caratteristiche Prodotto

Andere merken in Niet gecategoriseerd