Advantech ADAM-5095 handleiding
Handleiding
Je bekijkt pagina 14 van 96
ADAM-5000 Series User Manual 6
4. First, with the correct zero (offset) calibration resistance connected as shown
above, issue a Zero Calibration command to the module using the Calibrate
option in the ADAM utility software.
5. Second, with the correct span resistance connected as shown above, issue a
Span Calibration command to the module using the Calibrate option in the ADAM
utility software. Note that the module zero calibration must be completed prior to
the span calibration.
1.2.2 ADAM-5017 8-ch Analog Input Module
The ADAM-5017 is a 16-bit, 8-channel analog differential input module that provides program-
mable input ranges on all channels. It accepts millivolt inputs (±150mV, ±500mV), voltage
inputs (±1V, ±5V and ±10V) and current input (±20 mA). The module provides data to the host
computer in engineering units (mV, V or mA). This module is an extremely cost-effective solu-
tion for industrial measurement and monitoring applications. Its opto-isolated inputs provide
3,000 V
DC
of isolation between the analog input and the module, protecting the module and
peripherals from damage due to high input line voltage. Additionally, the module uses analog
multiplexers with active over- voltage protection. The active protection circuitry assures that
signal fidelity is maintained even under fault conditions that would destroy other multiplex-
ers. This module can withstand an input voltage surge of 70 Vp-p with ±15 V supplies. The
jumpers of ADAM-5017 are designed for current input. Refer to the diagram below for the
locations (JP1). Short the pin-head by the jumpers to set the channel to be current mode.
Note! If the above procedure is ineffective, the user must first issue an RTD
Self Calibration command $aaSi2 to the module and then complete
steps 4 and 5 after self calibration is complete.
Table 1.4: Calibration Resistances of ADAM-5013
Input Range
Code (Hex)
Input Range
Span Calibration
Resistance
Zero Calibration
Resistance
20 Pt, -100 to 100°C A = 0.00385 140 Ohms 60 Ohms
21 Pt, 0 to 100°C A = 0.00385 140 Ohms 60 Ohms
22 Pt, 0 to 200°C A = 0.00385 200 Ohms 60 Ohms
23 Pt, 0 to 600°C A = 0.00385 440 Ohms 60 Ohms
24 Pt, -100 to 100°C A = 0.003916 140 Ohms 60 Ohms
25 Pt, 0 to 100°C A = 0.003916 140 Ohms 60 Ohms
26 Pt, 0 to 200°C A = 0.003916 200 Ohms 60 Ohms
27 Pt, 0 to 600°C A = 0.003916 440 Ohms 60 Ohms
28 Ni, -80 to 100° C 200 Ohms 60 Ohms
29 Ni, 0 to 100°C 200 Ohms 60 Ohms
Bekijk gratis de handleiding van Advantech ADAM-5095, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Advantech |
| Model | ADAM-5095 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11670 MB |
