Adler AD 7062 handleiding
Handleiding
Je bekijkt pagina 8 van 160
8
To charge the device while the battery is mounted mounted on the device:
1. Assemble the dust cap onto the main body if not yet assembled.
1. Insert the charger plug into the hole located in the back part of the battery.
2. If you are charging the device not plugged in the device. The LED light on the battery will start to flash signaling charging. When the
battery is fully charged the LED light on the battery will stop flashing and will give off continuous light.
Using the device as a stick vacuum cleaner:
Use options: You can directly connect the attachments to the main body by using the front port of the device as shown on picture A2
page 4.
2. Insert the accessory onto the main body port as shown on picture A4 page 4.
1. Assemble the dust cap onto the main body if not yet assembled.
Empting the dust container:
The LED display on the top of the device (D3) will show you the charge progress. Once the battery is fully charged and the charger is not
disconnected the display will turn off after 30 minutes.
3. Each correct connection will be accompanied with a “click” sound. (If the option is present in the middle of the pipe there is a button
that will allow the pipe to bend).
2. Assemble the metal tube (2) onto the electro brush (3) and in turn insert the metal tube into the main device (1). As shown on picture
A3 page page 4.
1. Hold the device over the dust bin and release the lock positioned on the lower side of the device on the front. (picture A5 page 4).
2. The flap will open and the dirt will fall out.
Using the device as a handleld vacuum cleaner:
Removing the / Cleaning the dust container:
2. Twist the dust container with your other hand.
2. To remove the brush roller release the lock and remove the side cover. The lock and cover can be accessed from the underside of the
brush. As seen on picture A7 page 5.
5. The HEPA filter is located on the top of the multi-cyclone filter.
5. Allow the brush to dry completely.
6. Replace the brush roller and put the side cover back on.
1. Wipe the housing of the brush with a damp cloth.
Cleaning the filter:
2. open or remove the dust container as mentioned in the points in sections “Empting the dust container” and “Removing the / Cleaning
the dust container”.
After each use please make sure to empty the dust container and if you feel that the device is not correctly collecting dust or the icon
showing the airflow is blocked Error icon showing circle on the display (D2). You will need to clean the filter. To do so you will need
to disassemble the filter. To do so please follow the below steps:
3. Turn the multi cyclone filter clockwise to release the lock.
1. Press and hold the button on the upper part of the device as shown on picture A6 page 4.
6. Remove the HEPA filter and tap it out. DO NOT WASH IT. Please make sure to regularly replace the filter. Depending on the use of
the device. More frequent cleaning and replacement might be needed when using the device intensively. You can buy the filter from
your seller CR 7063.1
8. Allow the device to dry out.
4. Wipe the brush roller to clean or clean it under running water if necessary. Remove hair and other dirt if needed.
3. Close the flap again by pressing it firmly upward until the lock clicks into place again.
1. Turn off the device.
10. Insert the multi cyclone filter into the main device and tighten by turning it clockwise.
4. The container can be cleaned with a damp cotton cloth.
11. Close the dust container and put it back in its place.
4. Remove the filter by pulling downward.
3. Remove the brush roller from the side.
DO NOT IMMERSE THE ROLLER FULLY INTO WATER
7. Clean the multi-cyclone filter with a brush or dry cloth. Rinse with clean warm water if necessary.
Cleaning the motorized electric brush:
3. Pull downwards to remove the dust container.
9. Insert the HEPA filter back to its original position. The filter must be level and the seal must not be squashed.
Bekijk gratis de handleiding van Adler AD 7062, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adler |
| Model | AD 7062 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 15114 MB |
