Adler AD 7060 handleiding
Handleiding
Je bekijkt pagina 8 van 156
8
Preparing the unit for operation (Photo A page 3)
To prepare the device for operation, first complete the device. To do this:
1. connect the main unit (1) to the Flex Tube ™ and then the tube to the LEC scanner ™ brush (7).
2. you can also connect the brush directly to the main unit.
The crevice cap(10) and 2-in-1 brush (11) are also compatible with the Flex Tube ™ and the main unit.
Using the unit:
1. first prepare the unit for operation.
2. turn on the device by pressing the On/Off button (9).
3. the unit will turn on. To change the suction power, press the Mode Change Button (2) located on the
display. (Photo B page 3).
4. during use, the battery level will decrease.
B1. Device fully charged 100%
B2. Device charged at 70%
B3. Device charged at 30%
B4. Device not charged 0% (Display blinks)
Charging the device (Photo B page 3). Charging takes about 5 hours:
1. There is a charging port on the back at the bottom of the device. Plug the charger into the charging port
and then into a power outlet.
2. During charging, the device will indicate the charge level as follows:
B8. Device charged at 30%. 1 dash does not blink 2 blink.
B7. Device charged at 70%. 2 dashes do not blink 1 blinks.
B6. Device charged at 100%. All 3 dashes do not blink.
Emptying the dust container:
In order to clean the device you need to empty the container:
1. turn off the device.
2. move the device over the dust container.
3. open the dust container by pressing the dust container emptying button (8) as shown in photo C1 page 4.
4. shake the remaining dust from the center of the bin.
5. close the container by pressing it upwards as shown in photo C2 page 4.
Cleaning the filters Inside the dust container:
1. After emptying the dust container, reach inside the dust container. There you will find a mesh filter (13).
There is an open and closed padlock marking on the filter. Grasp the mesh filter securely to open turn the
filter towards the open padlock.
(2) Pull the filter and remove it from the dust container.
3. inside the mesh filter is the air inlet filter (14).
4. pull the built-in handle to separate the two filters. Inside the mesh filter is the inlet filter. Inside the inlet
filter is a rack. Remove the rack from the inlet filter. See illustration C5 page 4.
5.After separation, use a toothbrush to clean both filters to collect excess dust.
6.You can also wash both filters separately under a stream of clean water.
7.If you wash the filters, remember to dry them thoroughly with a paper towel and then let both filters dry in
a well-ventilated dry room.
NOTE: NEVER USE THE DEVICE IF THE FILTERS ARE NOT FULLY DRY. REMEMBER TO USE
THE UNIT ONLY WITH FILTERS INSTALLED. OTHERWISE YOU WILL DAMAGE THE UNIT.
8.After a certain period of time, despite cleaning and maintenance of the air inlet filter and outlet filter, the
performance of the vacuum cleaner will decrease. This is caused by wear and tear of the filters. In this case,
contact your dealer and replace the filters with new ones. Filter model: AD 7060.1.
9) After cleaning and drying the filters, install them again.
10. make sure that the mesh filter is properly installed and turned towards the closed padlock.
Replacing the exhaust filter (Illustration D page 5):
Bekijk gratis de handleiding van Adler AD 7060, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adler |
| Model | AD 7060 |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 16011 MB |
